Top Ceiling Metal Lath Reviews

Dunzy 150 Pcs 1 Inch Plaster Drywall Washers Metal Washers for Screws Plaster Repair Rings Plaster Buttons Profile Washer Flat Washers for Wall Ceiling Drywall Plaster Repair

• Sturdy Material: the plaster washers are crafted with steel and with zinc plated, and drywall screws are made of steel, which are sturdy and well made, and can serve you for a long time.
• Size Details: the plaster repair washers are about 1 inch in outer diameter, 5/32 inches in center hole, and screws are 1 inch in length, appropriate size for you to use.
• Complete Set: the package comes with 150 pieces of plaster repair rings in silver and 150 pieces of drywall screws in black, enough quantities and a nice set can meet your daily use needs, also can be kept as spare for accidental use.
• Helpful and Required: you can use these plaster buttons to fix the plaster against the lath, which can avoid sagging and cracking, maintaining your wall and ceiling in good condition.
• Toolbox Essentials: coming with small size and lightweight, the metal washers and screws can be easily stored in your tool cabinet, occupying a little space, convenient for you to take out as needed.

10000 #8 X 3/4 Phillips Modified Truss Head K-Lath Sharp Point Screw Zinc Plated Bulk Box 50 Lbs.

• Widely used for wood-to-metal applications such as metal lath in stucco/other to 22-18 steel studs..

Stainless Steel Lath Screws 8 x 3/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 3/4 0.75 in.

• Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
• ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
• REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
• it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
• HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
• MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Stud Finder Wall Scanner, M MARSIAN 5 in 1 Electronic Stud Locator with Auto Calibration, LCD Display and Sound Warning, Beam Finder Center Finding for Wood Metal Studs AC Wire Detection

• ...tion, and wait 2-3 seconds for calibration to be completed. It will complete once the decreasing bars disappear and the buzzer has beeped once.
• TH580 wall scanner can be applied to various wall surfaces, such as drywall, lath, plaster, wallpaper, wood flooring, painted walls, acoustic ceiling, etc. No matter you are a professional contractor or just want to make a home improvement project, the stud finder can protect you from danger and damage with accurate detection.

Stainless Steel Lath Screws, 8 x 1-5/8, Sharp Point Modified Truss Head Phillips Drive (Quantity: 100) Type 17 Cutting Point 305 (18-8) Stainless Steel, Length: 1-5/8 (1.625) in.

• Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
• ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
• REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
• it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
• HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
• MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Stainless Steel Lath Screws 8 x 1-1/4 Sharp Point Modified Truss Head Phillips Drive Quantity 1000 Type 17 Cutting Point 305 18-8 Stainless Steel Length 1-1/4 1.25 in.

• Wire-Lath Modified Truss Head Screws for Fastening metal lath to wood. IDEAL for ALL applications where a larger bearing surface is needed underneath the head. HEAD DIAMETER is 0.42 Inches. #2 Phillips Drive.
• ATTACHES WOOD OR LIGHT GAUGE METAL - Superior penetration through a variety of woods and thin metals.
• REDUCES WOOD SPLITTING - ELIMATES NEED FOR PRE-DRILLING - This thread cutting screw is ideal for use with wood.
• it offers a coarse tapping screw thread as well as a special long sharp point that is fluted in order to capture chips. The patented thread design and Type 17 point make drilling faster, reduce splitting, and allow these screws to be driven into most hardwoods without pre-drilling ..
• HIGH DEGREE CORROSION RESISTANCE: Passivated and Waxed Stainless Steel Type 305 (18-8). HIGH QUALITY STAINLESS STEEL: These #8 Wood Screws are high quality grade 18-8 Stainless Steel, giving the screws one of the highest forms of corrosion resistance and strength, making it last longer than other hardware on the market today. For use in Non-Magnetic environments.
• MODIFIED TRUSS HEAD - The rounded head top is much lower and flatter while the width of the head is wider, than pan or round screws of the same nominal size. The modified truss is basically a tru....

Stud Finder Wall Scanner - 5 in 1 Stud Detector with Intelligent Microprocessor Chip and HD LCD Display, Stud Sensor Beam Finders for the Center and Edge of Wood AC Wire Metal Studs Joist Pipe

• Accurate and Rapid: The stud finder adopts an intelligent micro-sensor chip with the highest sensitivity which can accurately and quickly find edges and center of metal, studs, joists, pipes, live AC wire behind walls, floors and ceilings. Fast detection saves users time and effort, making the task completion easier. No matter professionals, homeowner and DIY enthusiasts, it must be an ultimate choice.
• 5 in 1 Multi-function Detection: The upgraded 5-in-1 mode provides users with more detection needs. 1/2 inch scan mode locates the center and edges of wood and metal studs up to 1/2 inch deep.
• medium scan locates the center and edges of wood and metal studs up to 1 inch deep.
• Deep scan locates the center and edges of wood and metal studs up to 1.5inch deep.
• Metal scan detects metal (Ferrous and Non-Ferrous Metal) up to 2.36 inch deep.
• AC scan detects live unshielded AC wires up to 2 inches deep.
• Digital LCD Display & Audio Alarm: This stud finder comes with large LCD display and sound alarm, which can detect the exact location of the objects. When find the objects, the LCD display will indicate the direction and the intensity of beeping tells whether you are more close to the target. This LCD also features back-lit function which can provides a clear app....

Stud Finder Wall Scanner - 5 in 1 Stud Detector with Intelligent Microprocessor Chip and HD LCD Display, Stud Sensor Beam Finders for the Center and Edge of Wood AC Wire Metal Studs Joist Pipe (Black)

• Accurate and Rapid: The stud finder adopts an intelligent micro-sensor chip with the highest sensitivity which can accurately and quickly find edges and center of metal, studs, joists, pipes, live AC wire behind walls, floors and ceilings. Fast detection saves users time and effort, making the task completion easier. No matter professionals, homeowner and DIY enthusiasts, it must be an ultimate choice.
• 5 in 1 Multi-function Detection: The upgraded 5-in-1 mode provides users with more detection needs. 1/2 inch scan mode locates the center and edges of wood and metal studs up to 1/2 inch deep.
• medium scan locates the center and edges of wood and metal studs up to 1 inch deep.
• Deep scan locates the center and edges of wood and metal studs up to 1.5inch deep.
• Metal scan detects metal (Ferrous and Non-Ferrous Metal) up to 2.36 inch deep.
• AC scan detects live unshielded AC wires up to 2 inches deep.
• Digital LCD Display & Audio Alarm: This stud finder comes with large LCD display and sound alarm, which can detect the exact location of the objects. When find the objects, the LCD display will indicate the direction and the intensity of beeping tells whether you are more close to the target. This LCD also features back-lit function which can provides a clear app....

Tabbed Lath Washer 1-1/4 Diameter Galvanized 1,000 Box

• Used for the Attachment of Metal and Plastic Lath, Plaster Repair, Insulation Board, and Gypsum Sheathings.
• 4 Keyholes for Bonding of Plaster and Basecoats.
• 4 Tabs for Pre-Spotting Washer into Soft Material Such as Insulation Board.
• Center Hole will Accommodate Screws to #12.

StudPoP On the LEVEL magnetic stud finder

Strong-Point 86MZ 8 x 0.75 in Phillips Modified Truss R-W Head Screws Zinc Plated Box of 8 000

• Meets ASTM A 510 for carbon steel manufacturing..
• Multipurpose sheet metal screw for light to medium gauge applications..
• Zinc plating meets ASTM B 633 for electrodeposited zinc coatings..
• Material Application - Attaches wire lath to wood or light gauge metal..

Surebonder 55916 Heavy Duty 9/16-Inch Length Staples, Arrow T50 Type, 1250 Count

• Fits Surebonder models: 5690, 5600, 5685, 5800, 9600A.
• Use for insulation board, metal lath, roof covering, etc..

Ships Within 1 Biz Day from NV - Blue Boar Recessed Light Carbide Grit Hole Saw 6-3/8” Dia for 6 inch Lights: Fast Cutting in Drywall, Lath & Plaster, Hardi Board

• 1" deep - Hard tungsten carbide grit edge for a long life in abrasive materials.
• Continuous cutting edge for smooth cutting even in wood lath and plaster.
• Cuts through drywall, plaster (NO Concrete), CornHole board, fiber cement Hardie board, acoustical tile, ceiling tile.
• Attaches to standard 5/8”-18 2-pin mount hole saw arbor and works with Hole Pro HP1156 Large shield and Arbor kit for straight cuts.
• SHIPS WITHIN 1 BUSINESS DAY FROM OUR NV WAREHOUSE.