Top Bus bar Expansion Reviews

Dell - Dell Dimension E521 System Board

...nly in Japan. L1 cache: 8 KB first-level. L2 cache: 256-KB, 512-KB, or 1-MB pipelined-burst, eight-way set associative, write-back SRAM..
System Information: System chip set: Intel 865G. DMA channels: four. Interrupt levels: 24 APIC mode. System BIOS chip: 4 Mb (512 KB). System clock: 533- or 800-MHz quad-data rate..
Expansion Bus: Bus types: PCI and AGP. Bus speed: PCI: 33 MHz. AGP: AGP 1X, 4X, 8X. AGP connector: one low profile. AGP connector size: 172 pins. AGP connector data width (maximum): 32 bits. AGP video bus protocols: 4x mode at 1.5 V. PCI connectors: one low profile. PCI connector size: 120 pins. PCI connector data width (maximum): 32 bits..
Memory: Architecture: DDR SDRAM. Memory connectors: two. Memory capacities: 128-, 256-, 512-MB, and 1-GB non-ECC DDR SDRAM. Minimum memory: 256 MB. Maximum memory: 2 GB. Memory type: 333-MHz DDR SDRAM (non-ECC). NOTE: DDR 333 memory performs at 266 MHz on 400 front- side bus processors..
Drives: Externally accessible: one slimline optical bay. one slimline 3.5-inch bay. Internally accessible: one bay for 1-inch high IDE hard drive..

Check Stock

AOICRIE 5PCS PCF8574T PCF8574 IO Expansion Board Module I2C IO Expander Module (5 PCS)

✔I2C interface, I / O expansion module, two I / O scalability 8 I / O (up to 8 simultaneous use the PCF8574 expanded to 64 I / O).
✔Typical application: I / O resource shortage MCU I / O expansion.
✔Main resources: the PCF8574 I2C interface, 8-bit parallel.
✔Package Included: 5 x PCF8574 IO Expansion Board I/O Expander I2C-Bus Evaluation Development Module.
✔We highly appreciate all customers opinions to improve the selling, also if anything you unsatisfied, please contact us for probable best solution..

Check Stock

DaierTek 12V Bus Bar 6 x 5/16 M8 Terminal Studs 12 Volt Power Distribution Block with Cover Battery Bus Bar 12V - 48V Positive & Negative for Automotive Car Boat Solar System

【Product Name】- Battery bus bar terminal block, these busbars will come in pairs, include one positive bus bar (red one) and one negative bus bar (black one)..
【Terminals & Rating】- Each 12v power distribution block includes - 6 x M8 (5/16") terminal studs. This battery distribution block can handle voltage @ Max 300V AC, 48V DC, and continous amperage @ Max 130A AC, 150A DC..
【Round Corner Base】 - The 12v bus bar is unique round corner base design, which makes the battery terminal block unique and special, looks more extraordinary compared with other busbars..
【More Open Area Design Cover】 - The cover of this 12v power block will allow 180° wire lug installation and can meet variety kinds of installat methods of end terminals..
【Application】 - This marine power distribution block uses copper plates and stainless steel terminals as conductors, which enables the battery distribution block to work in extreme environment, suitable for automotive, car, marine, boat, etc..

Check Stock

Sonnet Fusion SSD M.2 4x4 PCIe Card

Adds ultra-fast SSDs to your system - Offers four M.2 NVME SSDs (sold separately) in your computer's x16 PCIe slot or Thunderbolt expansion chassis.
High performance PCIe interface - PCI Express 3.0 x16 host bus interface for high performance applications.
Outstanding performance - simultaneous data transfer speeds up to 12,000 MB / s (3).
Great way to add up to 8TB of M.2 SSD storage to computers with Thunderbolt - Perfect for use in Sonnets Echo Express III-D, Echo Express III-R, xMac Mini Server, xMac Pro Server and Thunderbolt expansion systems.
RAID support - Supports MacOS and Windows RA.

Check Stock

4 Post Power Distribution Block Bus Bar Pair with Cover - Made in The USA - 250 Amp Rating – Marine Bus Bar Automotive and Solar Wiring – Battery Terminal Distribution Block - Set of 2 3/8”

Ideal for Automotive, Solar and Marine Use - Our 250 AMP 4-post power distribution block busbar is ideal for automotive, car audio, solar, and marine use. Whether you need to consolidate, distribute, or protect your electrical system, our bus bars are excellent for managing wires and distributing power..
Includes Both Red and Black Connectors - With these 2 packs of 4 post power distribution blocks, you will have plenty of connection points for both positive and negative wiring terminals with 3/8" holes. The 4-way bus wiring block will make setting up your electrical systems quick, neat, and easy..
Anti-Corrosive & Even Consistent Flow - Our bus bars 12v are anti-corrosive and constructed to handle high currents. The nickel-plated brass contact plate ensures even and consistent flow and stability. Wire up to 4 accessories. Each bus bar terminal block includes a cover to protect connections from damage and corrosion..
Keep Your Wires Neatly Organized- With these power distribution blocks you can finally organize your wiring, so it doesn't look like a rat’s nest under the hood anymore. Use our power distribution bars for your car, truck, RV, boat, Yacht, Solar systems, and any other cable combination you can think of..

Check Stock

Heart Horse Bus Bar Terminal Block 1/4 Power Stud Battery Junction Block Post Distribution Block Insulated with Cover DC 48V 150A for Auto Truck RV Boat 1/4 ,Red+Black

WORKING RATING - Power stud size: 1/4".Maximum working voltage is DC 48V & up to 150 Amps.The battery bus bar is measured 1.77" x 1.69" x 1.4"..
EASY TO USE - Each bus bar with a cover can prevent short circuits and is completely safe.The cable can be installed with a wrench without removing the cover..
DURABLE & DEPENDABLE - The bus bar has good electrical conductivity and corrosion protection for durability.Terminal block's material is stainless steel, insulated base..
EFFICIENTLY DISTRIBUTE POWER - With these power distribution block, you can organize your wiring cleanly and keep your environment clean and tidy..
APPLICABILITY - Battery junction block is widely used in motorcycles, cars, trucks, RVs, etc..

Check Stock

Bopaodao Copper Bus Bar 3mm x 25mm x 5.91 inch / 150mm, 1Pcs C110 Pure Cu Copper Flat Buss Bar Stock

1Pcs c110 copper flat bus bar, 3mm x 25mm x 5.91 inch / 150mm, about T 1/8" x W 1".
Copper flat bars are widely used for electrical applications for the high electrical and thermal conductivity. Due to its exceptional strength, ductility and corrosion resistance, copper flat bar is also typically used in architectural applications. Uses of copper flat bar include automotive, construction, machined components, roofing, industrial, electrical, fabrication, engineering, manufacturing, marine equipment, architecture industries.
As a factory seller, we would like to accept any customization about the copper bar, including the length, drilling and bending or any other special needs, please contact us.
The copper bar is made of 0.999 copper, which is the C110 Cu, we also provide tinned copper bar and Nickel-plated copper bar.
Copper bars are also called copper bus bars or copper buss bars. They are made of copper and have rectangular or chamfered (rounded) rectangular cross-sections. (Nowadays, rounded copper bars are generally used to avoid tip discharge). The circuit plays the role of conveying current and connecting electrical equipment. Sometimes it can also be made as crafts or decorations.

Check Stock

CalFlor KI75155 VersaBlock Tapping Block FlooringInstallKit

Pull bar and tapping block are built tough to withstand countless floor installations.
Heavy duty tapered pull bar, designed to be used on laminate and engineered flooring.
8 mm reusable, wedge-shaped, stepped expansion spacers.
Solid heavy duty tapping block, not hollow, non-breakable.

Check Stock

NESGLODUO Copper Flat Bar - Copper Bar Stock, Copper 110 Flat Bar, 0.24in x 1in x 12in

【Size】It is a solid bar of copper: 12''L x 1''W, 0.24'' thickness and weight is 14.11 ounces, no more no less, good size for the electrical project you're looking for..
【Material】Copper flat bar is made of copper, grade as C-110. It's thick enough and conducts heat well, so burn through is mitigated, if you need something to soak up heat this works well..
【Features】Easy to cut and drill, and work great for your intended use. My uncle easily fabd a bus bar system for his new X-S-3400s, good investment compared to custom machined pieces that are 3-4x the cost..
【Copper 110 Flat Bar】It would carry current with no issues and work well for your project such as make a bud bar for electrical project, or bus bar for battery connections..
【Application】Copper flat stock is suitable for various milling, craft, lathe, knife project, battery terminal L brackets, home solar battery bank, or others electrical engineering..

Check Stock

Victron Energy Lynx Power in Battery Connector

The lynx power in module is used to connect batteries via an external fuse, It can be useful if you have multiple parallel strings.
The Power In contains a negative and positive DC bus-bar with M8 bolts in which to connect batteries cables.
It can take cables up to 22 mm in diameter through the bottom entry guides, and no limit via the two side connections.
A modular DC bus bar, the Victron Lynx Power In is used to connect batteries to the Lynx DC distribution system.
Incorrect installation can be hazardous, Please consult a licensed professional and follow all applicable electrical codes during installation.

Check Stock

MOTU MIDI Express 128

MIDI connectivity - eight independent MIDI inputs and outputs (128 MIDI channels).
Expansion - add additional MIDI ports by plugging in another MOTU MIDI interface.
Works with your favorite software (includes drivers for Mac OS X and Windows).
With rack ears attached, fits standard 19" racks at 1U high.

Check Stock

Andifany PCIE 2S Serial Port Card DB-9 Pin -232 Serial Industrial COM Port Expansion Card AX99100 for PC

Compatible devices: serial connected devices, serial network/monitoring equipment, data acquisition systems, POS terminals and industrial PCs, serial I/OUSB for add-on cards, I/O expansion for embedded systems.
2S + SPI (PCIe to dual serial and SPI) and LB (PCIe to local bus/ISA)-Like) are suitable for different types of applications..
AX99100 is a single-chip solution that can fully integrate PCIe 2.0 Gen 1 endpoint controller and SerDes with various peripherals, such as two/four high-speed serial ports, one parallel port, I2C master, high-speed SPI, local Bus (ISA-Like)) and GPIO..
Composed of four main configurations, such as 2S (PCIe to Dual Serial), 2S + 1P (PCIe to dual serial and single parallel),.
Single-channel (X1) PCI Express endpoint with integrated PHY controller.

Check Stock

8 Terminal Bus Bar Terminal Block 10 Pack Brass Wire Screw Terminal for Car Boat Marine Ground Power Distribution Terminal Block

Brass terminal grounding strip bus bar block with 8 screws & 2 Stud.
High quality plastics base ensures great mechanical strength and durability.
Use M4 screws to fix it in place through the two screw holes on both ends of the terminal.
Widely used in power distribution cabinets, distribution boxes,mechanical equipment factories,electrical equipment factories,etc.

Check Stock