Top Board Connector Reviews

Treedix 4pcs USB Type-C Breakout Board Serial Basic Breakout Female Connector Type PCB Converter Board

  • With this USB breakthrough, you will finally be able to integrate the USB-C connector into your project without soldering every tiny SMD pad.
  • This upgraded USB-C breakthrough board has powerful power, three times the power of the previous USB. The breakthrough board adds resistance to the original foundation.
  • This USB-C breakthrough board is reversible, so it also solves the general frustrating problem of USB cables.
  • This board introduces the VBUS, GND, CC1, CC2, D+ and D- pins of the USB-C connector into a 0.1" pitch connector, while providing up to 1.5A nominal power and up to 3A power, It depends on the upstream equipment.
  • Use it to replace the charging port on the astro a50 headset. It can be said to be perfect. There are positioning holes on the breakout board for easy fixation. The hole on the Type-c USB is large enough and the connector size meets the association standard..
Check Stock

uxcell 17pcs DIP IC Chip Socket Adaptor Round 28 Pin 2.54mm Pitch Dual Row 15.24mm Row Pitch

  • Row to Row Distance(Approx):15.24mm/ 0.6".
  • As the carrier of the IC chip, the IC connector can replace the chip and PCB board for repeated welding and disassembly without damaging the chip, achieving the effect of saving IC cost and time.
  • When installing,first solder the chip to the IC connector, and then solder the IC connector to the PCB board.
  • when you need to install or replace the chip, directly remove the connection between the IC connector and the PCB board, without changing the chip and connector Connection..
  • Advantages-IC connector has strong vibration and heat resistance, can withstand repeated welding and disassembly, convenient installation, and easy to use.
  • Noted - The spacing and line spacing of the connector holes must be the same as the spacing and line spacing of the chip pins.
Check Stock

uxcell 20pcs DIP IC Chip Socket Adaptor Solder Type 2.54mm Pitch Dual Row 8 Flat Pin 7.6mm Row Pitch

  • As the carrier of the IC chip, the IC connector can replace the chip and PCB board for repeated welding and disassembly without damaging the chip, achieving the effect of saving IC cost and time.
  • When installing,first solder the chip to the IC connector, and then solder the IC connector to the PCB board.
  • when you need to install or replace the chip, directly remove the connection between the IC connector and the PCB board, without changing the chip and connector Connection..
  • Advantages-IC connector has strong vibration and heat resistance, can withstand repeated welding and disassembly, convenient installation, and easy to use.
  • Noted - The spacing and line spacing of the connector holes must be the same as the spacing and line spacing of the chip pins.
Check Stock

Treedix Prototype Breakout Breadboard Adapter Expansion Board for BBC Micro:bit

  • This is a connector that fits directly to the edge contacts of a BBC micro:bit. The connector has 80 pins, but because of the different widths of the micro:bit edge contacts, some of the micro:bit contacts will map to more than one of this connector's pins. Also, the back half of the pins are not used at all..
  • The edge connector gives access to all the important pins on the bottom edge of the micro:bit. Check the datasheet for the pin spacing and orientation. This connector is best used with a custom PCB..
  • This breakout board for edge connectors allows intermediate and advanced users to connect micro:bit to breadboards and other sensors, motors, LEDs, etc..
  • We can use it in many ways, it is highly recommended to use our breakout board.
  • Through the breakout board, we broke through all 21 GPIO, power and ground pins in the form of 0.1"..
Check Stock

SparkFun MicroMod LoRa Function Board - 1W 915M30S LoRa Module Frequency Range: 900 - 931MHz Transmit Power 28.5 - 30dBm (max) Modulation LoRa, FSK, GFSK, MSK, GMSK, OOK Antenna Impedance: 50Ω

  • The 1W LoRa MicroMod Function Board adds LoRa capabilities to your MicroMod project. It is intended to be used in conjunction with a MicroMod processor board and a MicroMod main board, which provides the electrical interface between a processor board and the function board(s)..
  • Utilizing the 915M30S LoRa module from EBYTE, which is a 1W (30dBm) transceiver based around the SX1276 from Semtech. There is a robust edge mount RP-SMA connector for large LoRa (915MHz) antennas.
  • with modification, a U.FL connector is also available. We've successfully tested a 12 miles line-of-sight transmission with this module (user results may vary)..
  • Board Features: M.2 MicroMod Edge Interface, Keyed Screw Slots, RP-SMA Antenna Connector, Configurable U.FL Antenna Connector. MicroMod Peripherals Used: 5V Power.
  • 1W 915M30S LoRa Module Features: Based on SX1276 chipset from Semtech.
  • modulation: LoRa, FSK, GFSK, MSK, GMSK, OOK.
  • Data Rate: FSK: 1.2 - 300kbps, LoRa: 0.018 - 37.5kbps.
  • Note: A MicroMod Processor, Main Board, and antenna are not included with this MicroMod LoRa Function Board. These parts will need to be purchased separately.
Check Stock

XT30 XT60 Balance Board RC Lipo Battery Parallel Charging Board,2 in 1 PG Parallel Charging Plate XT30 XT60 Plug Supports 4 Packs for 2S-6S Lipo Battery

  • 2 in 1 lipo battery parallel charging board lipo charger,supporting XT60 connector and XT30 conector lipo battery.It is just a parallel charging board, not a diret charger, need to connect with a charger which support the balance port ( JST connector).
  • Thicken PCB copper foil, allow security using 35A charging current..
  • This lipo balance charging board supports up to four packs of the same type, same cells 2S-6S lipo battery pack,such as 2S lipo battery,3S lipo battery ,4S lipo battery,5S lipo battery,6S lipo battery..
  • Equipped with 40A fuse between any two groups of batteries, to prevent line burned due to the large battery pressure.
  • Output Connector:XT30 connector /XT60 connector,support xt30 and xt60 lipo batteries..
Check Stock

SparkFun MicroMod ATP Carrier Board-Modular Interface Ecosystem-Connect microcontroller/Processor Board to Various Carrier Board peripherals

  • Access all the pins (i.e. ATP) of the MicroMod Processor Boards with the SparkFun MicroMod ATP Carrier Board! This board breaks out the MicroMod Processor Board's pins on the M.2 connector to 0.1" spaced female headers and PTH pads on the edge of the board..
  • Features: M.2 Connector. Operating Voltage Range: ~3.3V to 6.0V (via VIN to AP7361C 3.3V Voltage Regulator). 3.3V (via 3V3).
  • Ports:1x USB type C, 1x USB type A Host, 2x Qwiic Enabled I2C, 1x CAN, 1x I2S, 2x SPI, 2x UARTs, 2x Dedicated Analog Pins, 2x Dedicated PWM Pins, 2x Dedicated Digital Pins, 12x General Purpose Input Output Pins, 1x SWD 2x5 header. Note: Depending on the design of the Processor Board, not all the pins may be accessible..
  • Additional Features: 1mAh battery backup for RTC. Buttons: Reset, Boot, LEDs. Power. 3.3V. Phillips #0 M2.5x3mm screw included.
  • Carrier board only. MicroMod processor board will be needed to use..
Check Stock

OLLGEN Auto Car OBD2 16 Pin Connector 16 Pin Male Connector Adapter Standard 16 Pin Male Plug OBD Shell OBDII PCB Diagnostic Tool Blue

  • Male Adapter with PCB: It can connect circuit board or weld line with PCB board.The shell is easily four inches long, plus a spring strain relief. you....
  • The soldier pads inside the shell do not have all the pins broken out, but you can just solder to the pin connections directly for odd pin outs. Note....
  • Used to build a breakout box:Lots of cars do not have 16 pin connector,such as some old cars. However now lots of diagnose tool is 16 pin connector,so....
  • Notice:It is just a small connector,do not have any accessory or software.Has a circuit board you could tack connections..
  • Package Include:Standard 16Pin Male Plug x 1.
Check Stock

3S 12V 40A PCB BMS Protection Board for 18650 Li-ion Lithium Battery Cell Module

  • This protection board is suitable for 3 series 3.7V 18650 li-ion cell..
  • The protection board is for cell Li-ion batteries, it can be used for ternary batteries, manganese acid batteries and cobalt acid batteries..
  • Support overcharge protection,overdischarge protection,overcurrent protection and short circuit protection..
  • This protection board is suitable for 3 series 3.7V 18650 Li-ion cell.Charging connector and discharging connector are separated..
  • Stable charging and discharging the various protection features such as precise overcharge protection,overdischarge protection,overcurrent protection....
Check Stock

uxcell 1.0mm Pitch 20 Pin to 20 Pin Extension Connector Aapter for FFC FPC Cable Extend Zip HDD

  • [Specification]: 20 Pin to 20Pin 1.0mm Pitch for 20 Pin FFC Cable.
  • [Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
  • [Type]:This is 1.0mm pitch FPC connector extend adapter for make longer install..
  • [Package]:1 x Pin to Pin 1.0mm Pitch FPC Connector Extend Adapter.
  • [Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..
Check Stock

uxcell 0.5mm Pitch 20 Pin to 20 Pin Extension Connector Aapter for FFC FPC Cable Extend Zip HDD

  • [Specification]: 20 Pin to 20 Pin 0.5mm Pitch for 20 Pin FFC Cable.
  • [Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
  • [Type]:This is 0.5mm pitch FPC connector extend adapter for make longer install..
  • [Package]:1 x Pin to Pin 0.5mm Pitch FPC Connector Extend Adapter.
  • [Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..
Check Stock

uxcell 0.5mm Pitch 20 Pins to 20 Pins Extension Connector Aapter for FFC FPC Cable Extend Zip HDD

  • [Specification]: 20 Pin to 20 Pin 0.5mm Pitch for 20 Pin FFC Cable.
  • [Feature]: FPC extension Board PCB support,connection from button board/Converter board to mainboard.
  • [Type]:This is 0.5mm pitch FPC connector extend adapter for make longer install..
  • [Package]:1 x Pin to Pin 0.5mm Pitch FPC Connector Extend Adapter.
  • [Application]:FPC is finding wide acceptance in the computer industry,particularly in such applications as Lap Top,Palm Top and Note Pad computer..
Check Stock

SparkFun Auto pHAT Compatible with Raspberry Pi Google Coral NVIDIA Jetson and More All in One Robotics Package Quickly add functionality to Single-Board Computers Drive 2 Small DC Motors & 4 servos

  • 4245 PSOC and 2-channel motor ports programmable using Qwiic library. On board ATTINY84A supports up to two DC motor encoders. PWM control for up to four servos..
  • 5v pass-through from RPi. Uninhibited access to the RPi camera connector & display connector. USB-C for powering 5V rail (Motors/Servos/backpowering Pi).
  • On board ICM-20948 9DOF IMU for motion sensing accessible via Qwiic library.
  • Qwiic connector for expansion to full SparkFun Qwiic ecosystem. External power inputs broken out to PTH headers. Designed for stacking, full header support & can use additional pHATs on top of it.
  • Raspberry Pi or other Single-board computer not included..
Check Stock