Top Bevel Gear Load Capacity Reviews

EXAUTOPONE Stainless Steel Bevel Gear Set AR44 Compatible with AR44 Heavy Duty RC Car Bevel Gear Set 30T/8T

  • 32 teeth for use with L149Y-P mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

1PC 90-Degree reversing Angle Gear Right Angle Gear Steering Small Bevel Gear Box Bevel Gear Speed Ratio 1:1 (A)

  • 16 teeth for use with PA4416Y-G mating bevel gear in 4:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L153Y-G Bevel Gear, 1.5:1 Ratio, 0.750\ Bore, 10 Pitch, 30 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 30 teeth for use with L153Y-P mating bevel gear in 1.5:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear L147Y-P Bevel Pinion Gear, 2:1 Ratio, 0.188\ Bore, 20 Pitch, 10 Teeth, 20 Degree Pressure Angle, Straight Bevel, Steel

  • 10 teeth for use with L147Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

PGFUN 2 Pcs 1M 20 Teeth 5/6/8mm Shaft Hole Tapered Bevel Gear 1:1# 45 Steel 1 Module 90 Degree Steering Gear with M5 Fixing Hole (5 mm)

  • 18 teeth for use with L152BY-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Unhardened teeth for applications where hardness and strength are not needed to transmit torque and motion.
Check Stock

Boston Gear HL148Y-P Bevel Pinion Gear, 2:1 Ratio, 0.375\ Bore, 16 Pitch, 12 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Steel with Case-Hardened Teeth

  • 12 teeth for use with HL148Y-G mating bevel gear in 2:1 gear ratio applications.
  • Straight bevel 90 degree mesh transmits mechanical power between perpendicular shafts.
  • Pressure angle of 20 degrees for a lower contact ratio between gears, resulting in higher load capacity than smaller pressure angles.
  • Low carbon steel (0.2 percent carbon) for applications where the hardness and strength of higher levels of carbon are not needed to transmit torque and motion.
  • Case-hardened teeth for applications where hardness and strength are needed to transmit torque and motion.
Check Stock

CNBTR 2PCS 45# Steel 2 Modulus 20 Teeth 14mm Hole Dia 90 Degrees Tapered Bevel Gear Wheel

  • Made of high quality 45# steel ,high wear-resistance,longtime use..
  • Lower contact ratio between gears, higher load capacity..
  • It only can fit for 2module gear,20 teeth,90 degrees,Hole Dia 14mm..
  • Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc..
  • Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth).
Check Stock

CNBTR Tapered Bevel Pinion Gear 12mm Hole Diameter 45# Steel 1.5 Module 16 Teeth Pack of 2

  • Made of 45# steel with high wear-resistance,strong and durable..
  • Lower contact ratio between gears, higher load capacity..
  • It only can fit for 1.5 module gear,16 teeth,90 degrees,12mm Hole Diameter..
  • Suitable for used in agricultural equipment, textile machinery, printing machinery, Mechanical transmission, etc..
  • Note:1 to 1 bevel gear (only 1 to 1 match, can not match with other modules and other number of teeth).
Check Stock

Bang II (Feat. Uppercase 5ive)

  • Fully milled gearbox housing made of 6061-T6 aluminum for the rear axle of ATOPRC.
  • Due to its dimensional stability results in a higher load capacity and service life of bevel gear and ball bearings. The problem of the torn fastening thread has an end with this case.
  • The bearing adapters are included in the set.
  • We recommend gluing the bearings with threadlocker y0113. For mounting the bearing adapters in the housing we recommend Bindulin silicone y19015. To use HD differential shafts y1477, the Atoprc bearing adapters must be machined.
Check Stock

Boston Gear G486Y-G Bevel Gear, 4:1 Ratio, 0.313\ Bore, 32 Pitch, 64 Teeth, 20 Degree Pressure Angle, Straight Bevel, Keyway, Brass

  • ★[OPTIMAL PERFORMANCE]: EXAUTOPONE premium Stainless Steel Bevel Gear Set made of premium stainless steel material improves gear mesh, and with delicate workmanship, which is durable and hard, and long service life..
  • ★[GREAT APPLICATION]:EXAUTOPONE premium Stainless Steel Bevel Gear Set provides over drive for the front axle, helping to pull car climb easily. And it can guarantee to meet the original equipment..
  • ★[FITMENT]:Compatible with AR44 axles, including a 8T bevel gear and a 30T bevel gear..
  • ★[HIGH QUALITY]:EXAUTOPONE premium Stainless Steel Bevel Gear Set is 100% brand new aftermarket unit built to meet OEM specifications. easy to install and remove, ideal replacement for the old or broken one. Factory price with higher cost-effective..
  • ★[PACKAGE & WARRANTY]:Package Includes 1 Pcs X 30T/8T Stainless Steel Bevel Gear Set . Any question just contact us, we will reply you within 24H.And we offer a 12 month warranty..
Check Stock

CNBTR 45 Steel 1.5 Modulus Silver 10mm Hole Diameter Tapered Bevel Gear Wheel 20T Pack of 2

  • [Product Type] Tapered Bevel Gear Wheel, 1.5 Modulus, 20T, 10mm hole diameter, 22mm overall length. Please confirm the correct size before purchasing..
  • [Material] Made of 45 steel material, not easy to wear, durable and lasting performance. This gear is an excellent industrial replacement accessory..
  • [Application] Used widely in conveying, hardware, agricultural equipment, printing machinery, automotive applications, mechanical transmission, etc..
  • The contact between the gears is firm, which ensures the normal operation of the machine and good bearing capacity..
  • Note: 1:1 bevel gear (can only be matched with 1:1, can not be matched with gears with other modules and T numbers)..
Check Stock

CNBTR 45 Steel 1.5 Modulus Silver 8mm Hole Diameter Tapered Bevel Gear Wheel 20T Pack of 2

  • [Product Type] Tapered Bevel Gear Wheel, 1.5 Modulus, 20T, 8mm hole diameter, 22mm overall length, Maximum Outer Diameter: 31.6mm/1.24". Please confirm the correct size before purchasing..
  • [Material] Made of 45 steel material, not easy to wear, durable and lasting performance. This gear is an excellent industrial replacement accessory..
  • [Application] Used widely in conveying, hardware, agricultural equipment, printing machinery, automotive applications, mechanical transmission, etc..
  • The contact between the gears is firm, which ensures the normal operation of the machine and good bearing capacity..
  • Note: 1:1 bevel gear (can only be matched with 1:1, can not be matched with gears with other modules and T numbers)..
Check Stock

Makita 5377MG Magnesium 7-1/4-Inch Hypoid Saw

  • Oil bath technology is created with a built-in fan and sealed gear housing to ensure 100% oil surface coating for less maintenance.
  • Make quick, one-handed adjustments using large, rubberized levers.
  • Better fit and more control with comfortable rubber grip on handle.
  • Large cutting capacity (2-3/8″” at 90°) and bevel capacity (0°-51.5°) with positive stops at 22.5°and 45°.
  • Settings are easy to read with oversized number and ruler markings.
  • Blade wrench is attached to saw for fast and convenient blade changing.
  • Large bevel capacity with positive stops at 22.5 degrees, 45 degrees, and 51.5 degrees..
  • Oil-bath technology is created with a built-in fan and sealed-gear housing to ensure 100% oil surface coating.
  • High quality, heat treated hypoid steel gears do not prematurely wear like traditional bronze-alloy worm drive gears.
  • Reinforced power cord withstands jobsite abuse.
Check Stock