Top Arduino Nano Ch340 Reviews

ACEIRMC for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (6 Pack)

  • download the driver of Nano V3.0 at: http://bit.ly/2jKlJMO.
  • Nano's got the breadboard-ability of the compatible for Board and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
  • The Nano is using the chips ATmega328P and CH340, not FT232 as official compatible for Arduino, so pls. use the driver from above link..
  • It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
Check Stock

Weewooday 6 Pieces Nano Board V3.0 ATmega328P Without Cable Compatible with Arduino Nano V3.0 with Pin Headers Pin Unsoldered

  • What you will get: the package included 6 pieces of nano board V3.0 ATmega328P, each nano V3.0 ATMEGA328P improved version with 3 pieces of pin headers unsoldered.
  • ATmega328P chips: using Atmega328P-AU MCU, support ISP download, using the same chips ATmega328P and CH340 with the official version.
  • Mini nano board: this is a portable, complete, and breadboard friendly board.
  • It has everything that compatible with Arduino has (electrically) with more analog input pins and onboard +5V AREF jumper.
  • Input and output: each of the 14 digital pins on the Nano can be applied as an input or output.
  • USB connection: the Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27).
  • The power source is automatically selected to the high voltage source.
Check Stock

Gowoops MEGA 2560 PRO Board Embed CH340G/ATMEGA2560-16AU Chip with Male pin headers, Compatible for arduino Mega2560 DIY

  • Embed version of Mega 2560 CH340G/ATmega2560 - compatible with Arduino Mega 2560 board..
  • Built on the Atmel ATmega2560 microcontroller and USB-UART interface chip CH340G..
  • Board have compact size 38x55mm. It is good solution, to make your final project on solder proto-board..
  • The board used the chip CH340G as converter UART-USB..
Check Stock

AITRIP 3pcs for Arduino Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module with 3pcs USB Cable Compatible with Arduino IDE

  • *The Nano is using the chips ATmega328P and CH340, Replace FT232RL..
  • *It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
  • *Nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other)..
  • *The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • *Arduino Nano V3.0 ATMEGA328P Improved version with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers)..
Check Stock

AITRIP 10PCS for Nano V3.0 ATmega328P Nano Board CH340 5V 16M Microcontroller Board, Compatible with Arduino Electronics Development Board

  • This board is using the chips ATmega328P and CH340, not FT232 as official Arduino.
  • More Breadboard Space:Nano's got the breadboard-ability of the Boarduino and the Mini USB with smaller footprint than either, so users have more breadboard space. It's got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND ）on one top, power and ground on the other..
  • The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper..
  • you will get 10pcs Mini Nano V3.0 ATmega328P 5V 16M Microcontroller.
Check Stock

AITRIP 10PCS ESP8266 NodeMCU LUA CH340 ESP-12E WiFi Internet Development Board 4M Flash Serial Wireless Module for Arduino IDE/Micropython

  • ESP8266 CH340 CH340G NodeMCU LUA ESP-12E WIFI Serial Wireless Module.
  • Built-in Micro-USB, with flash and reset switches, easy to program.
  • Compatible with Arduino IDE/Mongoose IoT/Micropython.
  • ESP8266 CH340 chip, power your development in the fastest way combinating with NodeMcu Firmware.
  • It's a IOT unit with all available resources on board, support smart link and smart networking..
  • ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area..
Check Stock

Treedix 2pcs ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

Treedix ATmega328P CH340 Development Board Compatible with Arduino UNO R3 Board Kit for Starter with Cable

  • The board is a microcontroller board based on the CH340. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button..
  • This is compatible board with an Atmega328p and a CH340G serial converter, 100% Compatible with Arduino UNO R3..
  • This board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit..
  • Friendly: the board is easy to use for Arduino starter, It contains everything needed to support the microcontroller.
  • simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started..
  • We strive to put our hundred percent to meet your requirements and try our best to achieve your satisfaction!.
Check Stock

ideaspark 3pcs ESP8266 NodeMCU CH340 ESP-12E WiFi Wireless Internet Development Board Serial Module with Micro USB Cable Works Great for Arduino IDE

  • ... MHz adjustable clock frequency. NodeMCU has 128 KB RAM and 4MB of Flash memory to store data and programs. Its high processing power with in-built and Deep Sleep Operating features make it ideal for IoT projects.
  • The NodeMCU Development Board can be easily programmed with Arduino IDE since it is easy to use.Works greate with Arduino/Mongoose IoT/Micropython.
  • CH340 replace CP2012 USB to UART Bridge ,provides a better performance plug and play interface solution and easier programming. Use the search engine Google.com or Bing.com earch for the keyword r "CH340 driver", it is very easy to find the driver installer.
  • Applications:Access points portals,IoT projects,Wireless data logging,Used in learning the networking fundamentals,Sockets and smart bulbs,Smart home automation systems.
Check Stock

FYSETC Display Screen SD-W-I-F-I with Card-Reader Direct BTT Wireless Cloud Transmission Module for Prus MK3S TFT35 V3.0 Ender 3 SKR Mini E3 3D Printer

  • Wireless transmission: a W-i-f-i-SD card adapter, Only supports 2.4G network, make sure the adapter and PC/Mac terminal connecting to the Same Network. Please note:Comes with a 8G card( detail user guides) in the package, not for using.Install is a little complicated, please reference the more information and other customers voice..
  • Usage: Make sure have a CH340 USB driver(search: FYSETC/CH340-Driver on Github) and a Arduino IDE software/Pronterface (Pronterface forces all caps, not good if SSID/PW has lowercase). Please refer to the product description at bottom for more details. Note: *Adjust the baud rate to 115200*on Arduino..
  • Based on ESP8266's low-power UART-W-I-F-I chip module. About the firmware. please search Github:FYSETC/ESPWebDAV..
  • Features: Maximum support 32GB of SD card.
  • The adapter uses a DHCP connection, please map its address as static in your DHCP server. Has the ability to operate in 802.11 B/G/or N modes. It is set to the "N" mode by default. To change modes requires modifying the firmware and re-flashing the device using the free Arduino IDE software..
  • Suitable for 24V 3D printer, such as Prusa MK3S,TFT35 V3.0, Ender 3,SKR Mini E3 V1.2 V2 etc. Need more help please email us, we will give you help within 24 hours..
Check Stock

Treedix USB to TTL Converter CH340 Module 3.3V/5.5v Serial Converter Development Tool with Micro USB Adapter for Arduino

  • Serial Basic Breakout Board CH340G serial signal serial ic breakout development board usb micro b connector save space diy electronics projects micro b cable jumper wires.
  • Base on USB converter IC CH340G, there is a wide range of operating systems . You may need to install drivers the first time you connect the chip to your computer's USB port or when there are operating system updates..
  • The output voltage is 3.3v by default, there is a 3.3v signal, it can also be changed to 5V, changing to 5V will cause the board to output 5V and 5V signals on the VCC pin(3 .3v to 5V by a short circuit selection).
  • There are two LEDs on the board connected to TX (green) and RX (yellow) for faster viewing of serial traffic.
  • Suitable for: Arduino Pro Mini, our GPS module, cellular module and many other devices that use serial communication.
Check Stock

ACEIRMC 6pcs Nano V3.0 3.0 Controller Terminal Adapter Expansion Board Nano IO Shield Simple Extension Plate for Arduino Mano AVR ATMEGA328P

  • Designed for Arduino for Nano V3.0: The item is a terminal expansion adapter, working very well for prototyping Arduino for Nano projects.
  • It lables for Arduino for Nano version 3.0, however you can still use this adapter for the older version (just have to remember that A0-A7 are in the reverse order)..
  • You can use this adapter to easily hook up for arduino for Nano to an outside world via hook up wires.
  • This item is a terminal expansion adapter, designed for Arduino Nano V3.0..
  • Nano Terminal Adapter Shield Expansion Board Compatible with Arduino Nano V3.0 AVR ATMEGA328P-AU Module.
Check Stock

AITRIP 2PCS Type-C USB CH340 5V 16MHz for Nano Board CH340/ATmega+328P , Type-C Connection Compatible with Arduino Nano V3.0

  • The Nano can be powered via the Type-C USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source..
  • Support for external 5V~12V DC power supply, Support power supply by 9V battery..
  • The Nano is using the chips ATmega328P and CH340, Replace FT232RL.
  • The Nano-C is breadboard-friendly and can be powered by USB, regulated 5V supply or unregulated 7-12V source. Connectors shipped unsoldered to fit the smallest of spaces.
  • Comes with 2packs of Nano V3.0 Micro Controller Module, each Nano V3.0 Micro Controller module is equipped with 3pcs pin headers (2pcs 15pin headers +1pcs 6pin headers), no welding needed..
Check Stock