Top Arduino Connector Reviews

Screw Terminal Block Breakout Shield Module for Arduino UNO R3

Terminal Block Breakout Shield Module - for Arduino UNO R3. the item has been soldered and assembled..
Terminal block pitch 3.5mm/0.138", wire size range 26AWG to 16AWG, strip length 5mm, screw M2 steel, pin header and cage copper..
Standard IDC40 pitch 0.1" header, you can use 40pin FRC(flat ribbon cable) connector cable connect all Arduino Uno pins to peripheral equipment..
With power on LED indicating. red reset button on the side. with a ICSP adapter connect header. FR-4 fiber glass PCB, dual copper layers..
NOTE: the item not include Arduino Uno module..

Check Stock

Arduino MKR Zero with Headers [ABX00012]

The Central Board for your Electronic Project.
Powerful 32-bit Microcontroller and Micro SD Memory Card Connector.
Ideal for: Music, Audio processing, robotics, art installations.
Part of the Arduino Maker Board Family for IoT Devices, easy to configure with Arduino Software..

Check Stock

Arduino MKR GPS Shield [ASX00017]

A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..

Check Stock

DZS Elec 6pcs 15cm 9V Battery Snap Connector Clip Lead Wire Experimental Battery Snap Power Cable for Arduino Project or LED Light Bar

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Use: Can be conveniently connected to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect or solder to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector Clip Lead Wire (NO battery included).

Check Stock

SunFounder Mega 2560 R3 ATmega2560-16AU Board Bundled with R3 Board and Ethernet Shield W5100 for Arduino

... ensure consistent and compatible with the original, but also easy to use..
R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory.R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
With this Ethernet Shield, for Arduino board can be used to connect to internet. Can be used as server or client. Directly plug puzzle board, no soldering required. It is directly compatible with Arduino official Ethernet Library. It adds a micro-SD card slot, which can be used to store files for serving over the network..

Check Stock

SunFounder Controller Board Compatible with Arduino UNO R3 ATMEGA328P ATMEGA16U2

Controller board compatible with Arduino UNO R3..
The board compatible with Arduino ATMEGA16U2 chip, Faster transfer rates and more memory.
Control using chip(compatible with UNO R3 ATmega328P chip).
Includes new pin configuration (SCL, SDA, IOREF).
Clearly print on the female header connector, more precise and easier to use the wire.

Check Stock

5 Pack Black Light Micro Effects Light 405nm Violet LED Mini Blacklight with 9V Battery Clip for Props Scenery Fluorescent Paints Theatrical Costumes UV Glow Inks

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Use: Can be conveniently connected to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect or solder to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector Clip Lead Wire (NO battery included).

Check Stock

AITRIP 5 PCS Pro Micro ATmega32U4 5V/16MHz Module Board with 2 Row pin Header Compatible with arduino Leonardo Replace ATmega328 Pro Mini (5PCS)

On-Board Micro-USB connector for programming.
Pay attention to : 1.When you open the for Arduino IDE software, could you please go to the tool and choose the board "for Arduino Leonardo".
2: The acceptable voltage range is 6 to 9 V..

Check Stock

Arduino Portenta H7 [ABX00042]

Two processors that can run tasks in parallel with both cores communicating with one another. Each core can execute Arduino, mbedOS, micropython, and TensorFlow Lite code..
Comes in the Arduino MKR form factor but includes two extra 80-pin high density connectors. Extend your Portenta H7 to physical interfaces like Ethernet connectors, CAN bus peripherals, extra GPIO pins, SD card, etc..
Onboard WiFi and Bluetooth connectivity up to 65 Mbps transfer rate (using an external antenna)..
Perfect for high-end industrial machinery, laboratory equipment, computer vision, PLCs, robotics controllers, or even dedicated stationary computers..
Main features: industrial temperature rates, 8MB SDRAM, 16MB NOR Flash, DisplayPort output, USBC connector, cryptochip for secure data transactions..

Check Stock

SunFounder R3 BoardBundled with Mega 2560 R3 ATmega2560-16AU Board for Arduin

R3 board compatible with Arduino. The board for Arduino use ATMEGA16U2 chip, Faster transfer rates and more memory..
R3 board control using r3 ATmega328P chip. Includes new pin configuration (SCL, SDA, IOREF).Clearly print on the female header connector, more precise and easier to use the wire..
The mega 2560 R3 Board is 100% compatible with Arduino. Powered via the USB connection or with an external power supply. The power source is selected automatically..
The ATmega2560-16au has 256 KB of flash memory for storing code (of which 8 KB is used for the bootloader), 8 KB of SRAM and 4 KB of EEPROM (which can be read and written with the EEPROM library). Comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files)..
This version is optimized in the original version, both to ensure consistent and compatible with the original, but also easy to use..

Check Stock

ELEGOO UNO R3 Board ATmega328P with USB Cable(Arduino-Compatible) for Arduino

Clear prints on the female header connector, more precise and easier to use the wire..
The ELEGOO UNO R3 BOARD now uses an 16U2 instead of the ATMega8U2 chip. Faster transfer rates and more memory..
Control using ATMEL ATMEGA+328P chip(the same with Arduino UNO R3).
100% compatible with the Arduino IDE and RoHS Compliant.
We have always cared about the customer experience and improve the product function details..

Check Stock

DZS Elec 6pcs 15CM 9V Battery Snap Connector Clip Lead Wire Experimental Battery Snap Power Cable With 5.5x2.1mm DC Male Plug for Arduino Project or LED Light Bar

Type: 9V T Type Battery Snap Connector, to power anything that running with a 9V battery..
Standard 5.5x2.1mm DC Male Plug, conveniently connect to other power module or Arduino board..
Cable: Approx. 15cm (6 inch) length, red wire for positive, black wire for negative, easy to connect to other equipment..
Application: Can be used for power supply or other 9V battery equipment, supplying power sourcec for Arduino Project or LED Light Bar etc. portable, easy to use..
Package: 6pcs 9V T Type Battery Snap Connector with DC 5.5x2.1mm Male Plug (NO battery included).

Check Stock

SparkFun Qwiic Pro Micro - USB-C (ATmega32U4) - Compatible with Arduino development board 5V/16MHz microcontroller AP2112 3.3V Voltage Regulator Castellated PTH pin pads Reset button Maximum 6V input

Small Compatible with Arduino board. Includes Reset button, 9x 10-bit ADC pins. 12x Digital I/Os (5 are PWM capable).
Improved version of the SparkFun Pro Micro. ATmega32U4 running at 5V/16MHz Supported under Arduino IDE v1.0.1+.
On-Board USB-C connector for programming. AP2112 3.3V Voltage Regulator. PTH Pads w/ Castellated Edges.
Hardware Serial Connections. Includes UART (i.e. Rx and Tx), Qwiic Connector for I2C, and SPI. Has onboard Reset Button. Input maximum of 6V. Dimensions: 1.3in x 0.7in..
The AtMega32U4 can have the bootloader overwritten if not used properly. There is a way to fix the bootloader if needed and instructions are available online. USB drivers may be needed to be installed on a computer to communicate with the board..

Check Stock