Top Arduino Boards Reviews

Developing Computer Skills - Binaural Beat Brainwave Subliminal Systems

  • 【Same function as the original Arduino】It great for learning the basics of how sensors and actuators work, and an essential tool for your rapid prototyping needs.
  • 【CHIP UPGRADE】Upgrade the main control chip to ATMEGA328P-AU.And it same as the original arduino pin layout. It compatible with all expansion boards..
  • 【ADDED A 500MA SELF-RECOVERYFUSE】Compared with the original ARDUINO, a 500ma self-recovery fuse is added, which automatically disconnects the circuit when short-circuited to avoid component damage.Change the plug-in pins of the original ARDUINO to SMD pins to avoid short circuit of the development board contact conductors, which is safer..
  • 【Added 10 LED marquees driven by MOS tubes】which avoids the problem of insufficient output current of the IO port of the single-chip microcomputer, and can directly drive a small DC motor through the IO port..
  • 【EASY TO USE】Change the original USB-B type interface to MICRO-USB interface, which is more convenient to use..
Check Stock

Arduino MKR Connector Carrier [ASX00007]

  • Works with any of the Arduino MKR boards: Zero, WiFi, LoRa, Sigfox, GSM, NBIoT, and Vidor..
  • Easily connect up to 14 Seeed Studio’s Grove modules to your MKR board..
  • Ideal for fast projects: plug several modules and go! No soldering required..
  • Screw terminals to safely connect the carrier board to a power source..
  • Connect sensors and actuators to the Arduino IoT Cloud and control them remotely!.
Check Stock

DollaTek GY-30 BH1750FVI Digital Light Intensity Sensor Module I2C Raspberry Pi

  • ANMBEST Pulsesensor Pulse Heart Rate Sensor is a plug-and-play heart-rate sensor for Arduino and Arduino compatibles..
  • Pulse Sensor adds amplification and noise cancellation circuitry to the hardware. It's noticeably faster and easier to get reliable pulse readings. The Pulse Sensor works with either a 3V or 5V Arduino..
  • The sensor can be worn on the finger or earlobe..
  • Supported development boards are Uno R3, mega2560, leonardo, 51 series, msp430 series, KL25Z. s..
  • NOTE: This product is NOT a professional medical device and should not be used to diagnose or treat medical conditions..
Check Stock

Arduino MKR GPS Shield [ASX00017]

  • A plug 'n' play shield for experimenting with monitoring fleets, high-altitude measurements, or any kind of project requiring localization of devices..
  • Arduino MKR GPS Shield uses the u-blox SAM-M8Q GNSS (Global Navigation Satellite System) module. It is meant to be used on top of boards in the Arduino MKR boards, but thanks to its Eslov connector, it is also possible to hook it up to any board..
  • It comes with a dedicated library that allows two different interfaces and offers a consistent set of APIs designed for a full usage of the GPS acquired information..
  • Operating voltage is 3.3V, but this shield comes also with an on-board holder for CR1216 batteries..
  • The MKR GPS Shield has an additional connector meant as an extension of the I2C bus. The extra I2C port, also referred to as the Eslov self-identification port comes with: SDA, SCL, GND, +5V, and an extra digital pin, meant to send an alarm to the otherwise plain I2C devices connected to it..
Check Stock

Purse Organzier Bag Organizer with Metal Zipper Large Beige

  • ★32 pieces double sided PCB prototype boards well packed in a plastic tray which is very easy to store and take out.
  • ★5 different size boards to meet your demands when designing your own Arduino kits, electronic experiments and DIY projects.
  • ★4 mounting holes at the corners of the board are very convenient for installing them together..
  • ★Pre-tinned plated holes on the board make it very handy to solder components and sensors for your projects.
  • ★High quality of durable glass fiber –FR4 material with 1.6mm thickness makes a very solid and sturdy prototype circuit board.
Check Stock

Ingcool 4G/3G/GNSS HAT Module for Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH,Jetson Nano, Based on SIM7600A-H, 4G/GNSS Module Support LTE CAT4 up to 150Mbps for Data Transfer, etc.

  • SIM7600A-H 4G HAT is a 4G/3G communication and GNSS positioning module, supports LTE CAT4 up to 150Mbps for downlink data transfer. it is pretty low power consumption.
  • Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/Zero WH series boards, Compatible with Jetson Nano, SIM7600A-H 4G module control pins can connect with host boards like Arduino/STM32.
  • Supports dial-up, telephone call, SMS, mail, TCP, UDP, DTMF, HTTP, FTP, etc. Supports GPS, BeiDou, Glonass, LBS base station positioning.
  • Connect the 4G module with computer to surf the Internet, or attach it onto Raspberry Pi to enable functions like 4G high speed connection, wireless communication, making telephone call, sending SMS, global positioning, etc..
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock

Breadboard Solderless Prototype PCB Board ALLUS BB-009 (3pcs) 400 Pin with 4 Power Rails and Double Sided Tape for Raspberry Pi and Arduino

  • Solderless breadboard is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino, Raspberry Pi, and other programming boards.
  • Easy to use: the breadboard is made of ABS plastic, each row and columns has corresponding letters and numbers, reduce the mistake handling.
  • Self-adhesive back tape makes it easy to stick on a platform, like the Arduino prototype shield.
  • With tight plug-in contacts, the components will sit well after assembly and nothing will wobble..
  • The jumper wires are easy to insert into the breadboard..
Check Stock

Treedix 5 pcs Prototype Shield Board Compatible with Arduino Mega 2560 Solderable Universal BreadBoard PCB Double Sided Tinned Gold Plated Holes

  • Perfect for Arduino mega sized base board and other programming boards.
  • Convenient for the prototypes and circuit design experiment and other DIY projects..
  • Used for electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits..
  • Standard IC spacing 2.54MM hole plated through among the pad can be perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc..
  • Electroless Nickel Gold finished prevent the copper on PCB from being oxidized and corroded and is good for soldering and touching..
  • Made of glass fiber FR-4 material, features high heat resistance, corrosion resistance, mechanical strength, insulation..
Check Stock

Arduino | Step by Step: The Ultimate Beginner’s Guide with Basics on Hardware, Software, Programming & DIY Projects (Arduino | Introduction and Projects Book 1)

  • Advancing the development of robotics technology w/ Earth's 2nd biggest & most advanced starter kit for Arduino. 65+ pieces w/ FIVE main boards: 100% Arduino-compatible Uno R3, Mega 2560, Nano V3, ESP32 WiFi+Bluetooth and ESP8266 NodeMCU development platforms.
  • Explore programming electronics with all of the most common sensors and modules in Arduino like RFID Card-Key Reader, Ultrasonic Sensor, Real Time Clock, Impact Switch, 3-Axis Accelerometer, LCD, Relay, Servo and Stepper Motor - suitable for beginner or advanced users.
  • Build wireless IoT Automation projects with ESP32 Development Board, HC-05 Bluetooth Module, ESP8266 Wi-Fi Module, 2x NRF24L01 Wireless Transceivers and the W5100 Ethernet Shield.
  • All-in-one bundle with extra accessories + 16G USB storage with free access to the GAR Dropbox Cloud including PDF guides & links to tutorials and videos to help you learn to program all the parts and get started quickly.
  • Effective technical/customer support from USA with lifetime replacement guarantee on all parts – The Monster comes in 16" x 12" durable orga....
Check Stock

Mxzzand 3in Industrial Robot Parts Accessories Omnidirectional Wheel Metal 2Pcs for Industry Production with 10pcs Driven Roller

  • 1 Sketch Pack, 12 Snap Connectors, 1 Gripper Pair, 2 Bridge Connectors, 3 Cube Connectors, 1 L Connector, 1 U Connector. 2 Snap Connector Caps, 2 3" Rectangle Connectors, 2 4" Rectangle Connectors, 2 5" Rectangle Connectors, 2 T Connectors, 8 Colored Foam Cubes, various screws and nuts.
  • 2 Arduino-Uno-Compatible Boards, 1 USB A-B Cable, 1 Joystick, 1 RGB LED, 1 Ultrasonic Distance Sensor, 8 Red LEDs, 8 Green LEDs, 8 Blue LEDs, 8 Yellow LEDs, 2 7-Color LEDs, 2 GRB LEDs, 12 220 Ohm Resistors, 12 10k Ohm Resistors, 1 LDR VT90N2 Photoresistor, jumper wires, 3 10k Potentiometers, 1 Fullsize Breadboard, 6 Push Buttons.
  • 1 9V Battery Holder, 1 Mini Breadboard, 1 Linkbot-Arduino Cable, 1 2-in-1 Dual Phillips/Slotted Screwdriver, 3 Snap Connectors, 1 Cube Connector, 1 L Connector, 3 Mounting Plates, 2 Sensor Bracket, 1 Li-ion Rechargeable Battery,.
  • 1 Color Sensor, 2 Short Distance IR Distance Sensors,1 RGB LED Module with Common Positive Lead (Common Anode), 2 RGB LED Module with Common Negative Lead (Common Cathode), 2 Ultrasonic Range Sensors, 1 IR Range Sensor, 1 Cable for IR Range Sensor, 2 Light Sensors, 3 Line Following Sensors, 2 Touch Sensors, 4 Sensor Brackets, 4 Sensor Inserts, 1 Universal Pan-Tilt, 3 Pan-Tilt Mounts, PDF file....
Check Stock

KEYESTUDIO Leonardo R3 Microcontroller Development Board with USB Cable Kit for Arduino Project

  • Please NOTE: Open the Arduino IDE, you’ll need to click the “Tools”, then select the Board that corresponds to your Arduino. If you don't choose the correct development board type, it will cause the compilation to fail to transfer. So this is a place that needs special attention..
  • The keyestudio Leonardo is a microcontroller board based on the ATmega32u4，It has 20 digital input/output pins (of which 7 can be used as PWM outputs), 12 analog inputs, a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button..
  • The Leonardo differs from other boards using separate USB-Serial chip in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor..
  • This allows the Leonardo to appear to a connected computer as a mouse and keyboard..
  • Has fcc and ce certification that they are made from environmentally friendly production technology and materials, made function,voltage, current testing before packaging.
Check Stock

Treedix 3 pcs Prototype Shield Board Solderable Universal BreadBoard PCB Double Sided Tinned Gold Plated Holes with Female Header Compatible with Arduino Mega 2560

  • The Breadboard Kit is convenient for the prototypes and circuit design experiment and other DIY projects. Perfect for Arduino mega board and other programming boards..
  • Used for electronic experiments and point-to-point DIY soldering projects, can be expandable with pin header and female header, designing your own Arduino kits..
  • Standard IC spacing 2.54MM hole plated through among the pad can be perfectly working with 3mm&5mm LED Diode kit, Electrolytic Capacitor kit, Monolithic Ceramic Capacitor kit, Resistor kit, etc..
  • Electroless Nickel Gold finished prevent the copper on PCB from being oxidized and corroded and is good for soldering and touching..
  • Made of glass fiber FR-4 material, features high heat resistance, corrosion resistance, mechanical strength, insulation..
Check Stock

5.65inch E-Ink Display HAT ACeP 7-Color E-Paper Module 600×448 Pixels eink Display epaper HAT Compatible with Raspberry Pi 4B/3B+/3B/2B/Zero/Zero W/WH,Jetson Nano,Arduino,Nucleo

  • SPI interface, for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc..
  • Advanced Color ePaper (ACeP) technology, supports 7-Color display.
  • No backlight, keeps displaying last content for a long time even when power down.
  • Ultra low power consumption, basically power is only required for refreshing.Onboard voltage translator, compatible with 3.3V / 5V MCUs.
  • Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32).
Check Stock