Top Annealing Machine For Heating Reviews

Yosoo 1000W ZVS Low Voltage Induction Heating Board Module Tesla coil 12V-48V Flyback Driver Heater DIY

  • This section of induction heating using low-voltage DC power supply 12-48V Maximum current 20A, maximum power 1000W..
  • Tested 53V power supply when working properly..
  • Because of its moderate power, can be used for small parts DIY players do hardening, annealing and other heat treatment, Also can be used with a graphite crucible melting gold, silver, copper, aluminum and other metals, uniform heating fast, very convenient..
  • 24V input with no load current of 3A , 48V input with no load current of 6A.
  • The higher the voltage, the greater the heating current when the same thing, the effect is better, But at the same time heat is also large, so to eradicate the actual situation to select the input voltage, the general use of the words 24V or 36V power supply is enough..
Check Stock

1800W ZVS Induction Heating Board Module Low Voltage High Frequency 12-48V Flyback Driver Heater with Tesla Coil and Cooling Fan

  • ...ooling fan interface, can also do Tesla discharge, generator voltage inverter, etc.
  • The induction heating circuit adopt 12-48V DC power supply, maximum current is 40A, the power uo to 1800W. It can work continuously under the condition of good heat dissipation. moderate power which make it can be used to quenching, annealing and other heat treatment. also for melted with graphite crucible kim/silver/ copper/aluminum and so on, heating is evenly and fast.
  • it is recommended that not exceed 48V 35A to prevent accidents and damage,Although withstand more than 40A current.Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small almost without response, and 12V power might lead to the voltage decreases, which is very dangerous.More than 24V/20A power supply, the greater the voltage/current, the greater the heating power, heating faster..
  • please check the power output meets the requirements if the MOS tube fever,and be sure to do a good job of cooling.Do not empty the board, otherwise it will create a very high noise, then MOS tube will burn out.
  • please do not to heat too large metal, otherwise it may be overloaded, please add a 35A fuse or ammeter and air switch for better use (not included)..
Check Stock

Ichimonji

  • The Sword is 100% Pure Hand Forged by Using Traditional Hand Forged Method: Annealing, Tempering, Quenching and Other Technology for Heating Processing.
  • The Blade is Hand Polished by Using 12 Different Ancient Polishing Methods and Made of High Quality Pattern-Steel.
  • the Blade is So Sharp that Can Easily Cut Through a Slice of a Paper and Cut Through Bamboo.
  • the Elliptical Guard(Tsuba) is Made of Premium Alloy and the Handle(Tsuka) is Wrapped with Black Colored Cotton Cord.
  • Auway Sword is Made in LongQuan, China Where Has a 2600-Years History of Manufacturing Sword.
  • Completely Handmade Sword with Stunning Workmanship.
Check Stock

Samurai Katana Japanese Full Tang Carbon Steel 1060 T10 Battle Ready Cold Real Handmade Damascus Heat Tempered  Sharp Knife

  • The blade is made by high carbon steel Damascus, hand-forged, Bamboo nails..
  • The Sword is 100% Pure Hand Forged by Using Traditional Hand Forged Method: Annealing, Tempering, Quenching and Other Technology for Heating....
  • The Blade is Hand Polished by Using 12 Different Ancient Polishing Methods and Made of High Quality Carbon Steel.
  • This product can be used to protect you from ferocious beasts during camping or outdoor activities. It can be given as a gift or for collection.
Check Stock

Supco CH5829 Range Bake Unit Heating Oven Element For Whirlpool Y04000066, PS1754668, AP4283357

  • OVEN BAKE ELEMENT – This high-quality part is a direct replacement for Whirlpool WPY04000066, AP6024122, Y04000066, 04000047, 04000066, 0E00105199, 1938-268, 1938-362, 1938-370, 1938318, 1938325, 1938370, 5-51119, 551119, 7-90208, 74004073, 7406P013-60, 7406P075-60, 790208, PS11757472, WPY04000066VP, Y04000047, Y0E00105199..
  • PREMIUM REPLACEMENT – The outside sheath is made of Incoloy, a very high temperature nickel stainless alloy. Sealed with a high temp liquid silicone compound straight out of the annealing oven..
  • HIGHEST-QUALITY PARTS – Supco CH5829 Range Bake Unit Heating Oven Element is designed to meet or exceed OEM specifications. Supco parts are built to last and a popular choice among repair technicians and DIYers..
Check Stock

Auway Hand Forge Short Japanese Katana Samurai Sword Carbon Steel Sharp Blade Wooden Sheath

  • Auway sword is made in longquan,china where has a 2,600 years history of manufacturing sword.
  • completely handmade sword with stunning workmanship.
  • The sheath are made of premium wood and the guard is made of alloy with a fine and exquisite daisy pattern.
  • The carbon steel blade is hand polished by using 12 different ancient polishing methods.
  • the blade is so sharp that can cut through bamboo.
  • The sword is 100% pure hand forged by using traditional hand forged method: annealing, tempering, quenching and other technology for heating processing.
Check Stock

Samurai Katana Japanese Full Tang Carbon Steel Sword 1060 T10 Battle Ready Cold Real Handmade Damascus Heat Tempered  Sharp Knife Musashi-1060 Steel

  • The blade is made by high carbon steel Damascus, hand-forged, Bamboo nails..
  • The Sword is 100% Pure Hand Forged by Using Traditional Hand Forged Method: Annealing, Tempering, Quenching and Other Technology for Heating....
  • The Blade is Hand Polished by Using 12 Different Ancient Polishing Methods and Made of High Quality Carbon Steel.
  • This product can be used to protect you from ferocious beasts during camping or outdoor activities. It can be given as a gift or for collection.
Check Stock

Sword fort Roronoa Zoro Swords Real Steel Handmade Katana Japanese Anime Cosplay Sword Yama Enma Arashi Sword-Black…

  • Katana is 100% handmade, with sharp edges and functions. It adopts traditional hand forging methods: annealing, tempering, quenching and other heating....
  • Sharp-the Blade is Hand Polished by Using 12 Different Ancient Polishing Methods and Made of High Quality Carbon Steel.
  • The katana’s handle is covered in the best Chinese grey 10mm cotton wire with excellent soft and anti slip performance, providing you with max....
  • The katana sword’s full length is about 40.55”/103cm, 27.76"/70.5cm blade, 10.43"/26.5cm handle..
  • Our products provide life-long quality assurance. If you have any questions, please contact us and replace them for free.
Check Stock

xinan2018 Samurai Katana Japanese Full Tang Carbon Steel Sword 1060 T10 Battle ReadyCold Real Handmade Damascus Heat Tempered Sharp Knife

  • The blade is made by high carbon steel 1090, hand-forged, Real white ray skin, Bamboo nails,no bo-hi (blood groove) ..
  • The Sword is 100% Pure Hand Forged by Using Traditional Hand Forged Method: Annealing, Tempering, Quenching and Other Technology for Heating Processing.
  • The Blade is Hand Polished by Using 12 Different Ancient Polishing Methods and Made of High Quality Carbon Steel.
  • the Blade is So Sharp That Can Easily Cut Through a Slice of a Paper and Bamboo.
  • This product can be used to protect you from ferocious beasts during camping or outdoor activities. It can be given as a gift or for collection.
Check Stock

Jihpensword,Samurai Sword,Full Tang Katana Sword,1060 High Carbon Steel,Very Sharp,Variety of Styles to Choose from - 41inch

  • 1.If you need a real katana, it's the right one.This is a black samurai sword.Made of 1060 high carbon steel,Full tang, strong,the razor is sharp and....
  • 2.Warning: It's sharp and Battle-Ready, and the black style is better for hiding in the dark like a ninja.Sharp, good looking and handsome katana.Will....
  • 3.The katana sword is handmade entirely in over 10 traditional processes, including Annealing, Tempering, Quenching and other technology for heating....
  • 4.This sword is a very good choice, gifts, cutting practice, display, and collection. It is durable enough.The sword is strong enough to cut through....
  • 5.Please note: the sword stand or holder is not included..
Check Stock

SH Scientific Laboratory Muffle Furnace SH-FU-5MGE (Tmax 1050℃/Continuous Running 900℃). 5L Chamber. Metal/Ceramic/Plastic/Titanium Thermal Treatment. Annealing/sintering/Melting/Combustion. 110V

  • Laboratory economic muffle furnace with flap door. Max temperature 1050℃. Recommended ideal running temperature is 850℃~900℃.
  • Water, soil, ceramic, metal, alloy, plastic and battery electrolyte analysis, heat treatment and innovation. Heating from 3 sides and single housing.
  • Excellent outgassing thanks to the exhaust air outlet on the head of chamber, i.e plastic polymer.
  • Light weight (22kg, 49lbs), 150x260x130mm internal, 5L, 1.5kW heater, 110V.
  • Universal use for metal and ceramic heat treatment including annealing, sintering, melting, combustion, ashing and densification..
Check Stock

SH Scientific Laboratory Muffle Furnace SH-FU-3MGE (Tmax 1050℃/Continuous Running 900℃). 3L Chamber. Metal/Ceramic/Plastic/Titanium Thermal Treatment. Annealing/sintering/Melting/Combustion. 110V

  • Laboratory economic muffle furnace with flap door. Max temperature 1050℃. Recommended ideal running temperature is 850℃~900℃.
  • Water, soil, ceramic, metal, alloy, plastic and battery electrolyte analysis, heat treatment and innovation. Heating from 3 sides and single housing..
  • Excellent outgassing thanks to the exhaust air outlet on the head of chamber, i.e plastic polymer.
  • Light weight (19kg, 42lbs), 130x220x110mm internal, 3L, 1.1kW heater, 110V.
  • Universal use for metal and ceramic heat treatment including annealing, sintering, melting, combustion, ashing and densification..
Check Stock

SH Scientific Laboratory Muffle Furnace SH-FU-11MGE (Tmax 1050℃/Continuous Running 900℃). 11L Chamber. Metal/Ceramic/Plastic/Titanium Thermal Treatment. Annealing/sintering/Melting/Combustion. 220V

  • Laboratory economic muffle furnace with flap door. Max temperature 1050℃. Recommended ideal running temperature is 850℃~900℃.
  • Water, soil, ceramic, metal, alloy, plastic and battery electrolyte analysis, heat treatment and innovation. Heating from 3 sides and single housing.
  • Excellent outgassing thanks to the exhaust air outlet on the head of chamber, i.e plastic polymer.
  • Light weight (34kg, 76lbs), 200x310x180mm internal, 11L, 2.8kW heater, 220V.
  • Universal use for metal and ceramic heat treatment including annealing, sintering, melting, combustion, ashing and densification..
Check Stock