Top 8 0 Engine Reviews

Anbull 7.5 HP 223cc Recoil Start Gas Engine Horizontal Shaft 3/4' x 2.43' Go Kart Gas Engine for Log Splitter Single Cylinder 4-Stroke Gas Engine Forced by Cooling OHV Motor EPA Approved

  • 【7.5HP High Performance Motor】Anbull 4 Stroke 7.5hp gas engine has a Max Output Power/Speed of: 5.5kW/4000RPM & Torque of 12.5Nm. Shaft Size: 3/4" Diameter, 3/16" Length. Keyway 5/16”-24 UNF. Compression Ratio of: 8.5:1. Bore x Stroke of: 70mm x 58mm. Valve Clearance (Cold) Intake: 0.05-0.10mm & Exhaust: 0.05-0.10mm..
  • 【Low Oil Sensor】The low oil shutoff functionality turns the engine off to prevent serious damage or failure when the gas engine at low oil level. Similarly, if the oil level is lower than required level when starting, it will not start..
  • 【Built-in Forced Air Cooling System】Transistorized Pointless (TCI) Ignition System, recoil start system and built-in forced-air cooling system keep the motor cool and delivers high reliability and durability operation..
  • 【Industrial Grade OHV Motor】Industrial grade OHV motor is equipped with higher combustion efficiency and allows your machine to run at higher speed..
  • 【EPA approved】 The horizontal shaft is mounted in the crankcase with dual ball-bearings, making this gas engine an ideal replacement for most standard engine configurations. The powerful gas engine features a durable cast iron cylinder making it the perfect replacement engine for a go-kart, log-splitter and dozens of other....
Check Stock

Engine Heater Kit compatible with INTERNATIONAL NAVISTAR 2001-2003 DT466, DT466E, HT530, DT530

  • Warms internal engine components for quick starts in cold weather and reduces engine wear by improving the flow of fluids.
  • Oil pan capacity: 1-3 qtrs. (0. 94-2. 8 L) | Hydraulic fluid capacity: Less than 1 gal (3. 8 L).
  • Volts: 120 | Watts: 50 | Amps: 0. 4 | Plug Type: 120 Volt, 15 Amp (Type A).
  • Includes Dow Chemicals XIAMETER SLT-5200 Acetoxy Blue Sealant.
Check Stock

DASBET Car Vacuum and Fuel Pump Tester Gauge Kit, Fuel Pump and Vacuum Tester Gauge, Leak Carburetor Pressure Diagnostics

  • Function: The Carburetor Carb Valve Fuel Pump Pressure & Vacuum Tester Gauge Test Kit enables testing of the fuel delivery pressure to the engine to check for worn or defective parts in fuel pumps and vacuum systems.
  • Professional Tester Kit: Fuel Pump Pressure & VacuumTester Gauge Kit, Carburetor Test enables testing of the fuel delivery pressure to the engine to check for worn or defective parts.
  • Diagnose leaking valves, incorrect timing, leaky intake manifolds, and clogged mufflers. Fuel pump operating pressures up to 10 PSI (0.7 Bar), Pressure gauge 0-28 IN-Hg (0-70 cm-HG) vacuum and 0-10 PSI (0-0.7 kg/cm²) pressure.
  • Easy-to-use: Includes a variety of adapters ideal for most vehicles.
  • 4-inch (10.2cm) diameter pressure gauge with color-coded measurement scales, 1.2-inch (3cm) thickness with rubber side notches, easy to read and grip.
  • Extra-long rubber hose and 14mm/18mm manifold adapter.
  • Rubber hose 40 PSI (2.8 Bar) maximum working pressure.
  • Easy Storage: All the tools are well organized in a storage case for easy transportation, simple storage, and quick identification.
Check Stock

Zerostart 3400060 Silicone Pad Heater Engine Oil, Transmission Fluid, Reservoir and Hydraulic Fluid Heater, 1¼\ x 3½\ | 120 Volts | 50 Watts

  • Warms internal engine components for quick starts in cold weather and reduces engine wear by improving the flow of fluids.
  • Oil pan capacity: 1-3 qtrs. (0. 94-2. 8 L) | Hydraulic fluid capacity: Less than 1 gal (3. 8 L).
  • Volts: 120 | Watts: 50 | Amps: 0. 4 | Plug Type: 120 Volt, 15 Amp (Type A).
  • Includes Dow Chemicals XIAMETER SLT-5200 Acetoxy Blue Sealant.
Check Stock

4000PSI Pressure Washer Pump Horizontal Shaft 1\ For EB4040HA With Honda Engine

  • 【Reborn Your Pressure Washer】YAMATIC Horizontal Power Washer Pump 3/4" Shaft MAX 3300 PSI / 2.5 GPM / @3400 RPM, Save money by replacing your pump instead of buying a new power washer. Top performance at 2800-3300 PSI and fit most 208-220cc 6.5HP-7.0HP engine. Replacement for Simpson, Generac, Homelite, Honda, Karcher and more. ※►Diagonal distance between screw holes is 3 5/8''. ►Hole Distance to hole is 2 9/16''. ►Key width 3/16''. ►Depth 2 5/8''. ⚠ Will not fit 7/8 inch shaft as engine..
  • 【Extended Durability】 High-performance double seal system prevents leakage, upgraded technical surfacing piston and bearing, It is manufactured from fully anodized die-cast aluminum for protection against rust, get 200 hrs running time, longer than OEM power washer pump. And the thermal relief valve (TRV) protects the pump from overheating while in bypass mode. ⚠NOTE: Will not fit 7/8 inch shaft as engine. If you're not sure fit or not, just message us and we will confirm it for you!.
  • 【Maintenance-Free】This pump features a maintenance-free crankcase so you never have to change the gasoline. This easy-to-install kit is great for power washers that can support 3300 PSI at 2.5 GPM to wash walls, fences, sidewalks, vehicles, and more..
Check Stock

JIFETOR Oil Pressure Tester Kit, Professional Engine Diagnostic Test, 100PSI Pressure Gauge Tool with Hose Adapter for Truck Car ATV

  • OIL PRESSURE TEST AND DIAGNOSTIC: JIFETOR engine oil pressure tester kit is used for measuring oil pressure on lubrication system quickly and accurately. The gauge readings assist to diagnose if there are following problems: blocking oil strainer or oil filter, broken pressure-limiting valve spring, poorly working oil pump, low/high oil viscosity, blocking lubrication oil channel, blocking oil filter core and by-pass valve is difficult to open etc..
  • FITMENT TYPE: The oil pressure test tool includes 3 sizes (1/8" NPT, 1/4" NPT, 3/8" NPT) selectable brass adapters, can be connected to the corresponding sizes oil pressure test service port, on most gasoline or small diesel engine, includes car, motorcycle, ATV, truck and so on, which oil pressure not exceeds 100psi..
  • PRESSURE GAUGE AND HOSE: Pressure gauge adopts rubber cover protected 3" large dial. 0-100psi and 0-7bar small scale range with big dial, very easy to read. No pressure holding function, return to zero automatically. The 30" long rubber nylon resin hose, is equipped with a 1/8" NPT brass adapter, can be connected to 1/4" NPT and 3/8" NPT adapters directly. Max working pressure: 300psi.
  • EASY TO OPERATE: When you want to test the oil pressure by this engine oil pressure diagnostic gauge, disasse....
Check Stock

49CC Motorized Bicycle Kit Bike Engine Kit Single Cylinder 4-Stroke Gas Petrol Motorized Bike Engine Scooter Belt Gear Fits Most 26' or 28' Bikes with V-Frame

  • ★【PROFESSIONAL ENGINE KIT】49cc 4 stroke pull start petrol conversion kit for adult bicycles, ideal for bikes with 26 inch frames and similar Long term spares available as required..
  • ★【MAIN PARAMETER 1】Engine Model：142F.
  • Engine Type：Air-cooled, 4-Stroke, OHV, single cylinder.
  • Bore x Stroke：41.8 x 36 mm (1.65 x 1.42 in).
  • Net Horse Power Output： 1.6kW (2.1HP) at 7,000 rpm.
  • Net Torque：2.7 Nm (2.0 lbs ft) at 4,500 rpm.
  • PTO Shaft Rotation Counterclockwise (from PTO shaft side)..
  • ★【MORE STABLE & HIGH SPEED】4 stroke engines are more stable, more reliable and quieter than the 2 stroke rivals. The top speed of between 27 - 32 MPH / or 43 - 51 KPHThe tank holds 2 litres of petrol and everything comes with the kit..
  • ★【MAIN PARAMETER 2】Ignition System：Transistorized magneto ignition.
  • Governor System：Centrifugal Mechanical.
  • Oil Capacity：0.25l (0.26 US qt, 0.22 Imp qt).
  • Fuel Tank Capacity (liter)：0.77l (0.81 US qt).
  • Package size: 53cm x 29cm x 29cm (20.9'' x 11.4'' x 11.4'').
Check Stock

ARTILAURA Speedometer Gauge Set - GPS Speedometer with Tachometer,Fuel Level Gauge Water Temperature Gauge Oil Pressure Gauge Voltage 4in1 Gauge for Car AUTO Boat Marine(White)

  • Gauge Set-GPS Speedometer with Tachometer, 4IN1 Fuel Level Gauge/Water Temperature Gauge/Oil Pressure Gauge/Voltage..
  • 【GPS Speedometer with Tachometer Wide Applicability】 The speedometer gauge indicating Range: 0-120MPH and 0-8000rpm. Indication light: LEFT, HIGH BEAM, RIGHT. Suitable for all vehicles Car/ Boat/Truck/Bus/AUTO and off-road vehicles..
  • 【4 in1 Gauge Multi-function 】【Alarm message】Alarm message, 1.Fuel.
  • 【Indicating Range】Engine oil pressure: 0~150PSI, Engine temperature: 100-250°F, Battery voltage: 8-16V, Fuel level: 0~ 100%. 0-190ohms for fuel level meter.
  • (Default 0-190ohms, can adjust to 240-33ohms).
  • ✅【Material】The AUTO gauge is made of Stainless Steel 316L Bezel, Rubber, Anti-fog Glass. IP67 waterproof and dustproof grade. Reverse polarity protection and anti-fogging performance. Standard 85mm (3 3/8") hole in the panel (II) and allow a clearance of 55mm (2 3/16”) behind the panel to fit the gauge..
Check Stock

Dr.Roc Replacement for Subaru Bumper Fender Clips with Fastenver Remover Kit for 90914-0007 90913-0067 90914-0051 91486-KJ010 90914-0063

  • Replacement for Subaru Clips OEM NO.: 909140007 (90914-0007)—Fender Liner / Engine Cover / Wheel well Clips —23/64"(10mm)Hole, Head Dia:13/16"(21mm).
  • Replacement for Subaru Fasteners OEM NO.:909130067 (90913-0067)—Bumper / Fender Liner / Mud flap / Engine cover / Grill Clips —5/16"(8mm) Hole, Head Dia:11/16"(18mm).
  • Replacement for Subaru Rivets OEM NO.: 909140051(90914-0051)—Front Bumper / Quarter Trim Panel / Cowl Trim Panel / Splash Shield / Headlamp Assy Clips —1/4"Hole(7mm),Head Dia:13/16"(20mm).
  • Replacement for Subaru Clips OEM NO.: 91486KJ010 (91486-KJ010)—Cowl Panel Vent Cap Clips —0.17"(4.4mm)Hole, Head Dia:0.72"(18.2mm).
  • Stem Length:0.54"(13.7mm)--15PCS. Replacement for Subaru Clips OEM NO.: 909140063 (90914-0063)—Cowl Vent Air Inlet Duct Push-Type Retainer Clips —0.27"(6.8mm)Hole, Head Dia:0.78"(19.9mm).
  • Premium OEM Upgraded Quality and Durable Subaru Clips Set —Made of Premium Auto Grade Nylon：PA66(Not Ordinary Cheap Nylon),solid like metal. Durable Fasteners & Fastener Remover with Conveniently Organized Box —15*4.4mm hole clips+15*6.8mm hole clips+15*8mm hole clips+20*10mm hole clips+15*7mm hole clips+1*....
Check Stock

Small Engine Tachometer Hour Meter: Timorn Digital Inductive Waterproof Tiny Tach Meter & RPM Meter & HR Meter for Dirt Bike | Chainsaw | Lawn Mower | Generator Motorcycle Boat Marine Outboard

  • Small engine tachometer rpm - Inductive tach gauge can display real-time rpm in digital when your engine is running. Help diaganose working condition of your vehicles & gas generator or equipment like boat, marine outboard motor, motorcycle, lawn mower, compressor, chainsaw, atv, dirt bike, tractor, truck, etc. The rpm meter tester with programmable rev limiter setting and max rpm recall keeps the engine safe. The recordable rpm range is 0-25000 and you can set the refresh rate at 0.5s or 1s.
  • Hour meters for small engines - Accurate unresettable tot running time, which is sum run time of all engines it meters. Resettable job time can record working time of two engines separately. That means you can track how many hours of two different equipment have worked with only one timer tool. When the engine is off or not working, the tot time remains visible. Time display range of this hr meter is 0-6000h, hour counter accuracy is 0.1h.
  • Maintenance reminder - Timing analyzer as hour/rpm checker can memorize the service time of two different engines in different time. When it's time to repair one of your engines, the tool's screen will show red backlit meanwhile the icon flashes as indicator to remind you. Tuning tachometer helps monitor your engine or car in go....
Check Stock

Alltooetools Double Ended Grip Valve Grinding Lapping Stick Tool Set 5/8" 13/16" 1-1/8" 1-3/8"

  • 【Applicable】Double ended grip valve grinding lapping stick tool set helps you properly match valve seats during an engine top-end rebuild. These tools include dual ends with oil and UV-resistant synthetic rubber cups that help you put the finishing touches on your tune-up..
  • 【Feature】6.75 inch (17.1cm) long Easy-grip handle for better control, less user fatigue, and more productivity. Oil and UV-resistant synthetic rubber cups..
  • 【Sizes】1-1/8 inch, 1-3/8 inch and 1-1/16 inch, 1-5/16 inch. Length: 8.9 inch and 7.9 inch (22.6cm and 20cm)..
  • 【Suitable】Suitable for any clean, flat surface of a lawn mower, chainsaw, or small or large engine car or other vehicle with 0.6 inch, 0.8 inch, 1.2 inch, and 1.4 inch (1.5cm, 2.0cm, 3cm, 3.5cm) valves..
Check Stock

JIFETOR Oil Pressure Gauge Tester Kit Engine Transmission Fluid Test Tool Set 12PCS, 500psi Automotive Mechanical Automatic Gearbox Line Pressure Meter for Car Truck Motorcycle ATV

  • ENGINE AND TRANSMISSION OIL PRESSURE TEST AND DIAGNOSTIC: This oil pressure tester kit is used for measuring oil pressure on lubrication system quickly and accurately. The oil pressure gauge readings assist to diagnose if there are following problems: blocking oil strainer or oil filter, broken pressure-limiting valve spring, poorly working oil pump, low/high oil viscosity, blocking lubrication oil channel, blocking oil filter core and by-pass valve is difficult to open etc..
  • EASY TO CHECK ENGINE OIL PRESSURE: Remove low oil pressure switch, attach the engine pressure tester with appropriate adapter, start engine to read the pressure on the gauge. Verify vehicle oil pressure is normal or not against manufacturer's recommended readings. Turn off the engine and remove the engine oil pressure tester, replace the low oil pressure switch, then done..
  • FITMENT TYPE: The transmission pressure gauge kit includes 12PCS selectable brass connectors (include the one on hose), very sturdy and durability. These connectors can be connected to the corresponding sizes oil pressure test service port, on most vehicles with gasoline or diesel engine, includes car, motorcycle, ATV, truck and so on..
  • PRESSURE GAUGE AND HOSE: Transmission pressure gauge adopts rubber cover pro....
Check Stock

X-PRO Long Case 150cc 4-stroke GY6 Air cooled Moped Scooter Engine with CVT Automatic Transmission, Electric/Kick Start…

  • 【Parameters】Engine type: Gy6 single-cylinder four-stroke, engine oil type: Sf15w-40 without oil, carburetor type: pd24j, carburetor type: horizontal vacuum carburetor, spark plug type: a7tc, ignition type: cfw, cooling: air cooling, oil number: >=87#, compression ratio: 9.2:1, clutch: shoe type automatic centrifugal dry clutch, transmission: cvt, ignition system: Cdi, starting method: electric/kick.
  • 【Specification】 Displacement: 150cc, maximum power (Kw/R/Min): 6kw/7500r/Min, rated power (Kw/R/Min): 5.2kw/7000r/Min, maximum torque (Nm/R/Min) : 7.6nm/6500r/Min, minute steady idle speed 1600±150r/Min, piston diameter: 57.4mm, piston stroke: 57.8mm, bore and stroke 2.26" X 2.28" (57.4mm X 57.8mm), lubrication capacity: 0.26 gallons (1200ml), cylinder working volume: 0.03 gallons (149.6ml), speed: 8 poles.
  • 【Features】 Large-flow oil pump: reduce friction pair wear and prolong engine service life.
  • aluminum cylinder head and cylinder block: improve heat dissipation, reduce weight, and increase engine torque.
  • crankshaft: engine low-speed high torque, crankshaft connecting rod adopts large diameter bearing, Increase the reliability of the bearing.
  • lubricating oil filter: help to remove solid pollutants in the lubricating oil, greatly reduce the wea....
Check Stock