Top 5v Motors Reviews

8PCS L298N Motor Drive Controller Board Dual H Bridge DC Robot Stepper Motor Compatible with Ardu-ino Electric Projects, Smart Car Robot

• Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors..
• The L298N driver module, using L298N chip can directly drive two 3-30V DC motor, and provides a 5V output interface, you can chip circuitry to 5V power supply, support 3.3VMCU control, you can easily control the DC motor speed and direction, you can also control the 2-phase stepper motor, smart car essential..
• Terminal driver part of the supply area VMS: +5V ~ +35V.
• Drive part of the peak current Io: 2A / Bridge.
• Logical part of the terminal power supply range Vss :4.5-5 .5V.
• Logical part of the operating current range: 0 ~ 36mA.
• The control signal input voltage range: 4.5-5.5V low 0V high.
• To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
• High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w..
• Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability, large capacity filter capacitance,afterflow protection diode, more stable and reliable..

AOICRIE 4PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper for Arduino

• L298N as Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects, Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability..
• Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient, To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage..
• Driving DC motor Because the module is drived by double H bridge,it can drive two motors simultaneously.Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled..
• Easy to Use No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use..
• Wide Usage Great for DIY Smart Car Robot Power MEGA R3 for Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits..

Kiro&Seeu L293D DC Motor Drive Shield Stepper Motor Drive Shield Expansion Board Compatible with Arduino Duemilanove Raspberry Pi

• This is a commonly used DC motor drive module, using a small current 293 chip DC motor driver chip..
• Using this chip you can use DC motors and power supplies of up to 10 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel..
• Tested compatible for Arduino Mega, Diecimila & Duemilanove..
• 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter..
• Multi-function, easy to operate, a strong driver library support and feature updates..

Hobbywing Hobby Wing 30120000 Quicrun 1625 Brushed ESC Vehicle Speed Controller (1/18 Scale)

• Kev rating/T Count: 2S LiPo: rpm≤30000.
• Vehicles: 1/16th, 1/18th touring cars/buggies/monster trucks.

Drone Follows Me Everywhere

• ... Long Flight Time】: Come with 2 intelligent batteries which support up to 50 minutes flight in total. Please charge the battery with 5V/3A or 5V/2A wall charger. It takes about 6.5 hours to fully charge the battery..
• 【Level 6 Wind Resistance】: The low noise brushless motors plus the level 6 wind resistance provide you a quieter and stable flight experience. Its ability to hover in one spot without worrying about it moving around makes filming simple and enjoyable as you watch on your phone..
• 【9800ft Video Transmission】: The F7GB2 drone has extended video transmission range up to 3km/9800ft, providing you crisp images and smooth video..
• 【Safe to Fly and Back】: F7 drone will return to home automatically when the signal is lost, low battery or the Return to Home is pressed. Don't have to worry about losing your drone..

Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board

• TB6612 motor driver with 1.2A per channel.
• 2 full H-bridges means you can drive 2-4 solenoids (only two can be active), two DC motors bi-directionally, or one stepper motor..
• Runs at 2.7V-5V logic. The motor & logic voltage are separate..
• Good for motor voltages from 4.5V up to 13.5V.

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

• Main driver chip L298N, strong driving ability, strong anti-interference, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
• Double H bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
• No assembly required. This L298N board comes ready to go. Just wire up motors and power, easy to use.
• External size 43*43*27mm / 1.69*1.69*1.06 inch, voltage 5V-35V, drive current 2A (Max single bridge).
• Great for Arduino DIY Smart Car Robot Power UNO MEGA R3 Mega2560 Duemilanove. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.

Stepper Motor HAT for Raspberry Pi,Jetson Nano Onboard Dual DRV8825 Motor Controller Built-in Microstepping Indexer Drives Two Stepper Motors Up to 1/32 Microstepping 5V 2.5A

• Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano.
• Protection features: Overcurrent Protection (OCP), Thermal Shutdown (TSD), VM Undervoltage Lockout (UVLO).
• Integrates 5V regulator, allows providing power to Raspberry Pi.
• 6 available microstepping modes, configured with the DIP switches: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step.
• Adjustable motor drive current via potentiometer, maximum 2.5A current output.
• Onboard dual DRV8825 motor controller IC with built-in microstepping indexer, drives two stepper motors, easy to use.
• Onboard multi connector options for stepper motors in different specifications.

Dilwe RC Boats 370 Water Cooling Pump with Motor Waterproof JR Plug Pump for RC Aircraft Carriers, Warships, Battleships

• Waterproof DesignThe RC water pump is waterproof and works well in water, JR plug suitable for plug into the receiver, plug and play..
• Long Working TimeUnder the condition of 5V voltage, the pump works continuously for 15 hours and pumps water continuously..
• Application forPut it to work normally, the temperature will be hot, but it belongs to the normal range and will not affect the use, suitable for RC aircraft carriers, warships, battleships, etc. on a series of remotecontrolled ships that require water cooling for motors and ESCs..
• Stable PerformanceThe power supply method is not to take power from the receiver, the battery used is greater than 2S and the voltage is between 728V, which is need to use a stepdown module to make the operation more stable..
• Special NoteThe RC water pump is suitable for installation on remote control boats that require water cooling with watercooled motors and without waterabsorbing steering gear..

L298P Shield R3 DC Motor Driver Module 2A H-Bridge 2 way For Arduino UNO 2560 NW

• Motor controller L298P, Drives 2 DC motors or 1 stepper motor.
• Max current 2A per channel or 4A max (with external power supply).

ZTW 30A ESC with 5V/2A BEC Output for Fixed Wing Airplane 2-4S LIPO (30A BEC)

• Super smooth, accurate and programmable throttle linearity and throttle response..
• Over temperature protection ,low voltage cut off protection ,signal loss protection and so on..
• Strong BEC output 2A/5V continuous and peak to 3A..
• Supporting high RPM motors and programmable by programming card and transmitter ..
• High efficiency with low resistance and low heat MOSFET and CPU.

SparkFun Auto pHAT Compatible with Raspberry Pi Google Coral NVIDIA Jetson and More All in One Robotics Package Quickly add functionality to Single-Board Computers Drive 2 Small DC Motors & 4 servos

• 4245 PSOC and 2-channel motor ports programmable using Qwiic library. On board ATTINY84A supports up to two DC motor encoders. PWM control for up to four servos..
• 5v pass-through from RPi. Uninhibited access to the RPi camera connector & display connector. USB-C for powering 5V rail (Motors/Servos/backpowering Pi).
• On board ICM-20948 9DOF IMU for motion sensing accessible via Qwiic library.
• Qwiic connector for expansion to full SparkFun Qwiic ecosystem. External power inputs broken out to PTH headers. Designed for stacking, full header support & can use additional pHATs on top of it.
• Raspberry Pi or other Single-board computer not included..

Hobbywing Ezrun 5V C4 Cooling Fan & 44 x 65mm Motor Heat Sink System RC Motor Fan For 1/8 Car#86080130 Blue,Get funshobby decal