Top 48re Low Stall Torque Converter 2 Reviews

B&M 20404 Tork Master 2400 Torque Converter

  • Replaces stock converter for better launch capability and more strength.
  • Value priced upgrade for mild performance applications and street rods.
  • Stall speed of 2300-2500 RPM (based on an engine producing 230 lb. ft. of torque at 2500 RPM).
  • High quality remanufactured unit features a new precision pump drive tube.
  • Backed by the manufacturer with a 1 year limited warranty.
Check Stock

AmpFlow A28-150-F48 Brushed, Fan-Cooled, Rare-Earth Neodymium Magnet Motor, 36V to 48V VDC, 7400 rpm

  • Measures 3.0 inches diameter (77 mm) by 5.1 inches long (129 mm).
  • Can be used with voltages ranging from 36V to 48VDC (or down to 24V with the appropriate fan).
  • Maximum power: 3430 watts (4.6 horsepower).
  • Maximum stall torque: 17.7 Nm (2500 oz-in).
  • Peak efficiency at 48V: 82% at 28 amps and 6750 RPM.
  • Power and torque at peak efficiency: 1100 watts (1.5 horsepower) and 1550 mNm (220 oz-in).
Check Stock

30 Series 6.5 HP 212CC Torque Converter Clutch Driver Pulley Go Kart/Mini Bike Comet Manco 3/4' Bore Max Torque Replaces,with 30 Series Go Kart Drive Belt Replace Manco 5959 / Comet 203589

  • 【30 Series Torque Converter and Go Kart Drive Belt】 ：New 30 Series 6.5 HP Go Kart/Mini Bike Torque Converter Clutch Driver Pulley Replacement Comet Manco 212CC. Recommended engine: 2HP-8HP. Interchanges with part numbers 219552A 30 Series Torque Converter Driver Clutch.3/4″ Bore Max Torque, with 30 Series Go Kart Drive Belt Replace Manco 5959 / Comet 203589..
  • 【Torque Converter】：This 3/4″ Torque Converter is a direct replacement kit for the most popular Comet TAV2 go-kart torque converter 30 series..
  • 【Wide Use–torque converter 3/4】: Small engine Torque Converter clutches are heavily used in go karts, mini bikes, and lawn mowers.For Go Kart, Mini Bike, Lawnmower, small tractors, Fun Kart, Golf Karts, mini choppers, ATV, motorcycles, and waterski winches etc..
  • 【Go Kart Drive Belt】: 30 Series Go Kart Drive Belt torque converter belt Replaces For manco 5959/comet 203589 murray 12-8487 baja Motorsports BB65-395 ken-Bar 300-009 255-299 rotary 8487. Width: 0.4″, Length: 27-1/32″..
  • 【Wide Use–go kart clutch belt】: The go-kart drive belt used on most Manco, American Sportworks and Ken-bar Karts with 5hp-7hp engines.Also used on the Comet TAV2 bolt on torque-a-verter kit.Center to center spacing for the driver and driven pulley ne....
Check Stock

TORCO-656LS 47RE 48RE EXTRA LOW STALL TORQUE CONVERTER for 5.9L

  • Diameter: 13.785" (47re 48re transmission) Extra Low Stall - REMANUFACTURED.
  • Please TEXT with any question 562 644 1534. After purchase, please provide your vehicle info: YEAR, MAKE, MODEL, ENGINE SIZE so that we can confirm....
Check Stock

212CC Torque Converter 6.5 HP 3/4 Go Kart Mini Bike Comet Clutch 10T 40/41 and 12T 35 Chain Predator Driver Pulley Replacement Set - 30 Series

  • 【Brand new predator 212cc 6.5 hp go kart torque converter clutch kit】 This 3/4" Torque Converter is a direct replacement kit for the most popular Comet TAV2 go-kart torque-converter 30 series. It fits all engines with a 3/4" Straight Crankshaft. Replaces Comet, Also Fits Manco Go Karts..
  • 【TAV2 30 Series Go Kart Clutch Kit】This torque converter fits a 3/4" shaft and comes with your choice of a 10 tooth sprocket for a 40/41 chain or a 12 tooth sprocket for a 35 chain. It will work with small engines producing 2-8hp. 30 series Asymmetrical design. Bring your off-road machine to life..
  • 【30 Series Toruqe Converter Belt for 6" Driven】 Length: 70.5cm / 27.76", Outside circumference: 27 23/64" , Width is 3/4".（1.9cm / 0.75"). Center to Center of driver and driven: 6-15/16 to 7"..
  • 【This clutch will help you get more power out of your small engine by reducing engine load】 A torque converter acts similar to a transmission, allows higher speeds out of your small engine, and smoother acceleration..
  • 【For your convenience this kit comes with】1 x 3/4" Driver Pulley.
  • 1 x 10 Tooth Sprocket for #40/41/420 Chain.
  • 1 x 12 Tooth Sprocket for #35 Chain(Chain not inclu....
Check Stock

30 series driver 3/4 clutch 30 Series 6.5 HP Go Kart/Mini Bike Torque Converter Clutch Driver Pulley Replacement for Comet Manco 3/4 Bore Max Torque

  • This 3/4" Torque Converter is made of high quality iron material,which is lightweight, portable, sturdy, durable, maximum torque, wear-resisting and....
  • This Comet Torque Converter kits fits for engines with 3/4" Straight Crankshaft, used in small vehicles, riding lawnmowers , small tractors, go karts,....
  • This 3/4" 30 series Torque Converter is a direct replacement kit for the most popular Comet TAV2 go-kart torque converter, Featuring 6" diameter with....
  • This 30 Series Go Kart Torque Converter Clutch 3/4" Replacement for Go Karts 30 series Engine Comet Manco, 3/4" bore designed for 6.5hp 212CC engines.....
  • 100% satisfactory service, if you have any questions, please feel free to contact us by email!We will solve it for you in the first time..
Check Stock

KENDA Juggernaut Tire 26 x4.00 Wire Clincher DTC 60TPI Black

  • 【Brand new predator 212cc 6.5 hp go kart torque converter clutch kit】 This 3/4" Torque Converter is a direct replacement kit for the most popular....
  • 【TAV2 30 Series Go Kart Clutch Kit】This torque converter fits a 3/4" shaft and comes with your choice of a 10 tooth sprocket for a 40/41 chain or....
  • 【30 Series Toruqe Converter Belt for 6" Driven】 Length: 70.5cm / 27.76", Outside circumference: 27 23/64" , Width is 3/4".（1.9cm / 0.75").....
  • 【This clutch will help you get more power out of your small engine by reducing engine load】 A torque converter acts similar to a transmission,....
  • 【For your convenience this kit comes with】1 x 3/4" Driver Pulley.
Check Stock

Golf Cart Converter 48V 36V to 12V Converter 12V 20A 240W Converter Voltage Regulator Reducer Transformer Waterproof Converter for Golf Cart Club Car

  • This DC-DC Converter was designed for 36V or 48V vehicles and it steps down DC 36V/48V to constant DC 12V voltage driving 12V appliances. 48 volt....
  • Voltage Converter Regulator, compact aluminum shell, strong and wear-resistant, better heat dissipation effect. IP68 Protection Level, epoxy resin....
  • 36 Volt to 12 Volt Converter, Intelligent Protection, With short-circuit, over-current, over-load, low-load, over-temperature intelligent....
  • High Conversion Efficiency, good stability, maximum transmission efficiency 96%, 100% full rated power, low calorific value, stable performance.....
  • The Dc-Dc Converter is widely used in golf cart, forklifts, led strip light, display screen of bus and taxi, monitoring system, large trucks,....
Check Stock

Mophorn Torque Converter CVT 2HP-7HP 3/4' Go Kart Clutch 212CC 30 Series Mini Bike 10T #40 41 Chain and 12T #35 Replacement Set TAV2 30-75 218353A Manco CVT Clutch Small Engine Drive Belt

  • Modified TAV2/30 Series: Our go-kart torque converter is the latest TAV2/30 asymmetrical series. The asymmetrical type system can reduce engine load and gain more power to bring your off-road machine back to life..
  • Updated Durable Belt: The new type of belt, go-kart asymmetrical belt 669, is one of the highlights for our torque converter for go-karts. Using this excellent elastic belt properly can improve the life span of your torque converter..
  • Quality Drive Clutch: We have a 3/4” Driver Pulley and a 5/8” bore driven pulley. They are made of aluminum and steel. And it also can fit for 4-8 hp small torque converter systems..
  • Vehicle Fitment: The torque converter is compatible with 3/4″ & 5/8″ straight crankshaft. You can usually use it on 4-8 hp go-karts and motorbikes..
  • Full Accessories: Our torque converter clutch has full accessories: 1 x 3/4″ driver pulley. 1 x 5/8″ bore driven pulley. 1 x plastic assy cover. 1 x aluminum mounting plate. 1 x driver belt. 1 x full mounting hardware..
Check Stock

BEMONOC Garage Door Motor 12V DC Right Angle Reversible Electric Gear Motor 45 RPM High Torque

  • Dc gear motor Dimensions: 175 * 62mm/ 6.88 * 2.44in(L * D).
  • ✔Out Shaft: 10mm shaft with 2 flats where flat to flat is 8mm and threaded end to fit a M6 tightening nut.
  • ✔Mounting: M6 screw holes, include 3 screws.
  • Main Material: Metal, Electronic component.
  • ✔Notice: the motor duty cycle is 100%, it can run continuously, it's our fault to make a wrong label, hope you can understand, any other questions....
Check Stock

Zipper Gap Buckle compatible with Neverfull Pochette Little Pouch Chain Strap Connective Buckle (Gold)

  • 【30 Series Torque Converter Clutch Kit】 This 3/4" Torque Converter is a direct replacement fits all models of Comet TAV2 Torq-A-Verters 218353A, 219552A, 219456A, 217610A. It fits all engines with a 3/4" Straight Crankshaft. Replaces Comet, Also Fits Manco Go Karts..
  • 【For your convenience this kit comes with both sprockets】This torque converter fits a 3/4" shaft and comes with a 10 tooth sprocket for a #40/41/420 chain and a 12 tooth sprocket for a #35 chain. It will work with engine sizes hp2 to 8hp. 30 series Asymmetrical design. Bring your off-road machine to life..
  • 【The Belt Feature】 Length: 70.5cm / 27.76", Outside circumference: 27 23/64" , Width is 3/4".（1.9cm / 0.75"). Center to Center of driver and driven: 6-15/16 to 7"..
  • 【Special function】This clutch will help you get more power out of your small engine by reducing engine load, A torque converter acts similar to a transmission, allows higher speeds out of your small engine, and smoother acceleration..
  • 【Go Kart Torque Converter Kit comes with】1 x 3/4" Drive....
Check Stock

MOOSUN 30 Series Torque Converter Driver Clutch 3/4' Bore Go Kart for Comet 219552 5957

  • This 3/4″ Torque Converter is a direct replacement kit for the most popular Comet TAV2 go-kart torque converter 30 series. It fits all engines with a 3/4″ Straight Crankshaft. Replaces Comet, Also Fits Manco Go Karts. Small engine Torque Converter clutches are heavily used in go karts, mini bikes, and lawn mowers..
  • Replacement for Go Karts 30 series Engine Comet Manco, 3/4″ bore designed for 6.5hp 212CC engines. Recommended engine: 2HP-8HP.
  • Featuring 6″ diameter with 3/4″ Bore, 3/16″ Key way. Interchanges with part numbers 219552A 30 Series Torque Converter Driver Clutch. With fine workmanship, this clutch can function well exactly as same as the original one..
  • This driver clutch is designed to work with a belt and driven pulley assembly. It is produced by the sophisticated technology. This clutch will help you get more power out of your small engine by reducing engine load..
  • Made of high quality iron material,which is lightweight, portable, sturdy, durable, maximum torque, wear-resisting and fast heat dissipation. It is the combination of elegance and easy to use, firmly and securely, guaranteeing the safety of your car..
Check Stock

JX CLS6322HV 0.07sec 21KG High Speed Coreless Digital Servo Ecoboost 180 Degree CNC Alum Shell Metal Gear for RC car Helicopter

  • Item name: Ecoboost CLS6331 30KG Servo 180° Coreless Motor Servo..
  • Stall Torque (4.8V): 23.26 kg.cm (322.99oz/in).
  • Stall Torque (6.6V): 30.64kg.cm (425.51oz/in)..
  • Dimensions: 40.5X20.5X40mm /1.59X0.80X1.57in.
  • Connector Wire Length: JR 265 mm (10.43in)..
Check Stock