XZT 3000psi(s16)-m22(Female) Pressure Washer Sewer Drain Hose,Sewer Jetter Hose Kit (50FT)
- Sewer Nozzle Outside Diameter Max.: 0.76″( 19.2mm).
- orifice: 1 Front(orifice is 1mm) 6 Back(orifice is 0.7mm).
- Connector: compatible most pressure brand.
Top 19mm Nozzle Reviews
Toro T5 Rapid Set Gear Driven Rotor with 5' Pop-Up Riser and Check Valve
- Arc adjustments from 40degrees to 360 degrees can be made quickly with a few twists for the turret – no tools required.
- The T5 RapidSet rotor comes with factory installed 3.0 gpm nozzle a full set of 8 standard nozzles (25° trajectory) and 4 low angle (10° trajectory) nozzles.
- Pop-up height: 5 inches (riser measured popped-up from top of cap to nozzle opening).
- Inlet 3/4 inch (19 mm), Body Height: 7.5 inches.
2 Pack Travel Bidet Bottle,Upside Down Peri Bottle for Postpartum Care,Portable Handheld 300ml Bidet Sprayer,Travel Bag Pointed Nozzle for Personal Hygiene Care,Perineal Recovery,Outdoor-Green Bottle
- MADE FOR BLAUX PORTABLE BIDET FOR TRAVEL - Experience a gentler, more complete clean with our replacement nozzles, designed for Blaux handheld bidet sprayer for toilet (not included). These premium portable bidet for women and men nozzles can be adjusted to face forwards or backwards and are super easy to wash and maintain. Experience superior personal cleanliness and reduce your toilet paper consumption with hand held toilet bidet replacement nozzles from Blaux..
- HAND BIDET TRAVEL NOZZLE TURNS 180° FOR ERGONOMIC USE - The Blaux bidet travel sprayer is like no other bidet bottle or diaper sprayer. Each replacement toilet shower nozzle is designed to maneuver 180 degrees, to ensure the maximum amount of surface area is covered for a more complete clean. Adjust the handheld personal bidet's nozzle manually to face forwards or backwards and make cleaning your undercarriage a comfortable and easy experience..
- EASY TO INSTALL REPLACEMENT NOZZLE FOR BLAUX PERSONAL BIDET - In a matter of minutes, you can have a bidet shower with warm or cold water set up and ready to go! To install, simply slide the existing bidet spray attachment off and replace it with a new electric portable bidet nozzle. It's that easy!.
- PACK OF TWO BLAUX BIDET PORTABLE REPLACEMENT N....
Makita PR00000034 1-3/8\ Welding Nozzle
- WELDING NOZZLE SUPPORT: PVC floor round welding nozzle with wheels, can be used with welding wire, with rollers to guide the welding seam straighter..
- WELDING NOZZLE WITH WHEEL: The welding nozzle with wheel can be directly fixed on the hot air gun. When there is a wheel, the wheel can be directly attached to the gap, and the gap can be filled evenly along the line of the gap, which can solve the manual filling of the weld. The filling is not straight..
- WELDING ROD SPECIFICATIONS: Hot Air Gun Welding Nozzle can use 3mm/4mm/5mm..
- WELDING NOZZLE WITH WHEEL ADAPTER: 8mm inner diameter of the heat gun nozzle, which can be matched with any other welding nozzle with an outer diameter of 8mm..
- MATERIAL: 304 stainless steel alloy, with good corrosion resistance and heat resistance, can withstand high temperatures of 800-1000℃, will not rust, oxidize, and deform under high temperature for a long time. It is an ideal accessory for plastic welding..
23 Pieces Caulking Finisher Kit Caulk Nozzle Applicator Stainless Steel Sealant Finishing Tool Caulk Nozzle Finisher Kit for Kitchen Bathroom Window, 23 Sizes
- Sufficient quantity: you will receive 23 pieces caulking finishers in 23 different sizes, abundant quantity and various sizes to meet your diverse caulking needs, provide nice sealing effect in different areas and angles.
- Sturdy material: our caulk nozzle applicators are made of quality stainless steel, which feature rust-resistant and anti-corrosion, easy to clean, durable and reusable.
- 23 Sizes: we offer you 23 size choices of the stainless steel sealant finishing tools, which will ensure different sealing requirements, the dimensions include 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 23, 25, 26, 28, 30, 35 mm.
- Practical and easy to apply: with the 45 degree nozzle design, our caulk nozzle finishers can achieve perfect filling without causing chaos and uneven finishes can soothe and fill caulk jobs easily, without leaving messy and uneven finishes, so as to save you a lot of time, practical and can be applied alone, easy to clean and reuse.
- Available occasions: our caulk nozzle applicators can be applied for various kinds of occasions, suitable for kitchen, bathroom, water tank, door, window, bathroom, sink joint filling finishing and more.
Funrous 3D Printer Nozzle Cleaning Kit, Stainless Steel and Brass Compatible with Mk8 Extruder Nozzles 0.2mm, 0.4mm, 0.5mm, 0.6mm, 0.8mm, 1.0mm Cleaning Tool for Cr-10, Ender 3/ V2 Ender3 Pro (37 Pcs)
- Nozzle Cleaning Kit: you will get 32 MK8 nozzles (including 4 hardened steel nozzles, 11 stainless steel nozzles and 17 brass nozzles), 5 nozzle cleaning needles (0.15mm), 5 cleaning brushes (0.15mm), 1 nozzle wrench, 1 L shaped socket wrench and 2 tweezers, sufficient quantity for you to conveniently replace it in time and achieve quality printing.
- And the input diameters of nozzles are 0.2 mm, 0.4 mm, 0.5 mm, 0.6 mm, 0.8 mm and 1.0 mm.
- Wide Compatibility of 3D Printer Extruder Cleaning Kit: MK8 extruder nozzle is suitable for 3D printer Makerbot, CR-10, MK8 and RepRap, Ender 3, Ender 2, Prusa I3, Prusa 3 and other 1.75 mm PLA ABS 3D printers.
- Reliable Material: the mk8 nozzle set is made of quality hardened steel, brass and stainless steel, strong and reliable, with higher hardness and rust resistance, wear resistance, heat resistance, easy to install and replace, serving you for a long life.
- Useful Nozzle Wrench 3D Printer Kit: the 0.15mm nozzle cleaning needle is made of stainless steel, flexible and sturdy, easy to bend into the nozzle without breaking, and greatly dealing with the blockage of the nozzle at the h....
VCT Deluxe Air Blow Gun with 4", 12", and 20" Long Angled Nozzle
- This 3 piece air blow gun kit is made of nylon construction and comes in sizes 110 mm/4.3", 300 mm/12" and 490/19.5" mm with ergonomic handles and squeeze trigger to adjust the amount of air output..
- The pistol design with ergonomic handle feels great in your hand and makes it very easy to use. Air inlet: 1/4"..
- Comfortable lever control and insulated handle.
- Angled Nozzle easily gets into tight places.
4 Pcs Soldering Nozzles for Hot Air Gun SMD Rework Station 853d 862d Replacement
- [Great Compatibility]: 4 Pieces of hot air gun nozzles include 3 round nozzles of 5mm, 8mm and 10mm and 1 square nozzle of 13mm, compatible for 853D, 878D soldering station and other hot air guns, applicable to our soldering station models: YES0367, YES0368, YES0369, YES0370, YES0371, YES0372, YES0373, YES0374, YES0375, any inquiry is welcome.
- [Practical Usage]: Nozzles of different size and shape are ideal for regulating the hot wind size and shape to heat different kinds of electronic components, 24mm diameter nozzle interface adapts to many hot air guns, easy to be installed.
- [Useful Lock Screw]: With lock screw for locking the nozzle firmly to avoid hot air flow out from the gap between the nozzle and the heat gun air outlet steel pipe, and reduce temperature irregularity.
- [Durable Material]: Sturdy and durable metal material not easy to rust and damage, suitable for long time use.
- [Soldering Nozzle Size]: 3 Round nozzles sizes are 5mm, 8mm, 10mm.
Wangdd22 15pc/Set 1.75mm Teflon Throat Tube+0.4mm Extruder Nozzle Print Heads+Heater Blocks Hotend for MK8 Makerbot Anet A8 3D Printer
- Pack of 5 x 3D Printer Extruder Hotend 30mm Length 1.75mm Nozzle Inputting Tube( for MK8 Makerbot Reprap Prusa I3 3D Printer) and 5 x 3D Printer 0.4mm....
- 0.4mm Extruder Brass Nozzle Print Head: Color - Golden.
- Compatibility: compatible with all 1.75mm PLA ABS 3D Printer.
- Quanlity:15pcs/lot (5 piece 1.75mm Nozzle Inputting Tube,5 piece 3D Printer 0.4mm Extruder Brass Nozzle Print Head,5 piece Heater Blocks Hotend).
16 Pieces 3D Printer Nozzle Wrench Cleaning Kit,10 Nozzle Cleaning Pins with Storage Box 2 Tweezers 2 Cleaning Copper Wire Brushes 2 L-Shaped Wrench Tool for 3D Printer Accessories
- 3D printer nozzle cleaning kit: you will get 10 pieces stainless steel nozzle cleaning pins in 5 sizes, 2 pieces cleaning copper wire brushes in....
- Nozzle cleaning pins: there are 5 different sizes, including 0.15 mm, 0.25 mm, 0.35 mm, 0.4 mm and 0.5 mm, allowing you to choose according to your....
- Cleaning copper wire brush: the brush is suitable for 3D printer nozzle hot bed cleaning and rust removal.
- When you use 3D printer nozzle brush to....
- Wrench and tweezer: 6 mm 7 mm L-shaped hexagonal wrench tool can be applied for fastening nozzles, and 6 mm wrench is compatible with mk8 nozzle.
- Quality material: cleaning pins are made of stainless steel, and wire brushes are made of copper wire, sturdy and flexible, not easy to break and....
Onyehn 22pcs/Lots A8&A2 3D Printer Part Each 5PCS 0.4mm Extruder Nozzle Print Head+1.75mm Teflon Throat Tube+Heater Blocks Hotend for MK8 Makerbot Reprap
- Pack of 5 x 3D Printer Extruder Hotend 30mm Length 1.75mm Nozzle Inputting Tube( for MK8 Makerbot Reprap Prusa I3 3D Printer) and 5 x 3D Printer 0.4mm....
- 0.4mm Extruder Brass Nozzle Print Head: Color - Golden.
- Compatibility: compatible with all 1.75mm PLA ABS 3D Printer.
- Quantity:22pcs/lot (5x 3D Printer Nozzle Throat Tube 5x Nozzle Print Heads 5x Heater Blocks Hotend 5x M6 nuts 2x Hex Key Wrenches (for MK8 Makerbot....
110V 1600W Professional PVC Roofing Welding Tools Heat Gun Kit Plastic Welder Hot Air Weld Gun with Roofing Seam Rollers Seam Tester Probe Weld Nozzle (Hot gun)
- 1pcs x Seam tester probe, plastic handle.
- 1pcs x 10" (250mm) Heavy duty roofing scissors.
- 1pcs x 5mm Round weld nozzle 1pcs x 5mm Round speed weld nozzle.
- [Warranty]: One year warranty, not include the heat element..
Megaforce
- 1 x 2.5mm Nozzle (1 nozzle was pre-installed to the spray gun).
- 1x True Micrometer Air Regulator with Gauge.
- This spray gun set is designed to provide equal atomization and partical size for all kinds of surface painting..
- It has control knobs for full adjustment over spray pattern, fluid control and air pressure. Contains 1.4mm/1.7mm/2.5mm stainless steel needles and nozzles set to meet your different applications.
- Light weight, ergonomic design and easy trigger pivot reduces operating fatigue..
- Ideal for spraying base coats, clear coats and other high viscosity coatings such as extreme high build or polyester primers, thick enamels, latex paints, chip guard, metal flakes, gel coats, liquid mask, etc. Two years warranty..