Top 12v Relay Power Reviews

12V 250A Winch Solenoid Relay Contactor Thumb Truck for ATV UTV 2000-5000lbs Winch with 6 Protecting Caps - Ovsor

【PRODUCT PARAMETER】- Voltage - 12V, power – 250A, capacity - 2000-5000lbs, for ATV Winch Solenoid Relay Contactor Switch 12V 250 AMP 1500lb-5000lb Application..
【HIGH QUALITY】 - Made of strong, weather-resistant steel and powder-coated black surface, with super durability. OEM of high quality KFI winch kit is a great alternative to replace contactor..
【MULTIFUNCTIONAL APPLICATION】- For ATV Winch Solenoid Relay Contactor Switch 12V 250 AMP 1500lb-5000lb Application. Direct Replacement for UTV ATV Winch Solenoid Relay Contactor Switch 12V 250 AMP..
【INSTALLATION GUIDE】- Easy to install. The two wires - Green and Black which go to the switch that controls In and Out on a winch. Blue and yellow go to motor, Black and red go to battery..
【AFTER-SALES SERVICE】- If the product fails or other problems, you can contact us at any time, we will solve the problem for you within 12 hours..

Check Stock

CW QRP Shortwave Radio Kit - CW Transceiver Shortwave Radio Kit

...er is used for if. After ta2003 multiplication detection, the sound size is adjusted by digital potentiometer and sent to audio active filter circuit. Finally, LM386 drives speaker, and if frequency supports calibration setting..
Use 3 bs170 parallel outputs, class E amplification, 12V power supply, output power 5W! Relay switching is used for transceiver, with the function of transmitting delay adjustment to avoid frequent relay switching and improve the isolation of transceiver channel..
It has the function of automatically sending call signs, which is very convenient to use. The MCU uses the original code of our store, which can adjust the code speed, sidetone frequency and sidetone size. It can input the call sign by itself (in automatic key mode) and support power down saving..
The PCB board of this kit can be conveniently put into the 88 * 30 * 120mm aluminum chassis (the shell needs to be prepared by itself, and the opening size of the front and rear panels is in the mesh disk). Main indicators Power supply: 12V Working current: receiving ≈ 120mA @ 12V.
Emission ≈ 1A @ 12V Transmitting power: 5W @ 12V Frequency range: 7.000mhz-7.100mhz, 1kHz / 100Hz step Working mode: CW transceiver, SSB receiver.

Check Stock

12V Speed Adjustable 2 Pin LED Electronic Flasher Relay for Motorcycle Turn Signal Direct Replacement Universal Hazard Warn Hyper Flash Relay Black,2pcs

【SPEED ADJUSTABLE】This LED flasher relay fixes motorcycle turn signal hyper flash, allow LED light to blink at the normal rate, Clockwise:SLOWER ,....
【APPLICATION】This 2-Pin Electronic Led Flasher Relay fit for most motorcycle/bike to fix the LED bulbs related turn signal light flashing, not....
【SPECIFICATION】Blinker Relay 2 Pin. Operating Voltage: 12V (11V-15V). Max Power: 42W. Switch Power: 0.02A to 12A. Working Temperature: -40°C to....
【PLUG AND PLAY】This Turn Signal Flasher Relay is plug-and-play. Work to directly replace Most Standard Factory 2-Pin Flasher. Eliminate the need....
【PACKAGE INCLUDED】2PCS Black adjustable 2 Pin motorcycle flasher relay for LED turn signal..

Check Stock

Hilitand AD22B04 12V Signal Decoder 4 Channel DTMF Tone Relay Phone Remote Control PLC

【12V】Working voltage is DC 12V, you can easily find suitable power for this relay..
【reverse polarity protection.】This signal decoder relay ahs reverse polarity protection which can extend the service life..
【8 modes】8 modes of operation: Non-locking (Momentary ), self-locking (Toggle), inter-locking(Latch), 5/20/60/120/250-second delay..
【default control】The default control command is 1/2/3/4. Example: Dial 1 to control relay 1, dial 2 to control relay 2, dial 3 to control relay 3, dial 4 to control relay 4.
control commands can be changed any 1-4 bits. (For more details, refer to "AD22B04_4 channel DTMF controller commands setting manual ")..
【operating current】Standby 11-13 MA, 1 relay "open" 44MA, 2 relays "Open" 77MA, 3 relays "Open" 110MA, 4 relays"open" 140MA..

Check Stock

Flasher Relay 3 Pin Adjustable LED Flasher Relay LED Flasher Blinker Turn Signal Light Blinker Universal for 12V 24V Automobiles and Motorcycles

12V 24V Flasher Relay: This is a superfine quality LED flasher relay universal for 12V 24V automobiles and motorcycles.
Practical and Durable: The LED flasher blinker is helpful in solving problems related to turn signal LED light, such as rapid flashing, no flashing or....
Stable Performance: This LED flasher relay adopts advanced SMD technology, features short circuit automatic protection, overload automatic protection,....
Easy Installation: The turn signal light flasher with standard 3-PIN connector design, easy to install, plug and play.
Working Parameters: The size of this turn signal flasher is 5.3 x 3 x 2.6cm / 2.1 x 1.2 x 1 inches, and its applicable power is 0.1-150W.

Check Stock

Electronic Specialties 193 Black 2.5' x 5' 12/24V Diagnostic Relay Buddy Pro Test Kit

Tests 5 different relays, both 12V and 24V and 3 diagnostic trouble codes help define the cause of the bad relay.
Kit Includes 5 Relay Adapters and blow mold case.
Fails bad relays - Good/Bad indication, green light for PASS, red light for FAIL with flashing trouble code.
Tests 5 different relays, both 12V and 24V.
3 diagnostic trouble codes help define the cause of the bad relay.
#193 Kit Includes 5 Relay Adapters and blow mold case.
Quick off-the-car relay tester - checks relay coil & switch contacts.

Check Stock

12 Volt Timer Relay, DROK 0.1s to 999min 50mA 4-Mode On-Off Automotive Digital Delay Relay, Electric Delay Timer Switch, Cycle Time Delay Module with LED Display

4 MODE TIME DELAY RELAY: DROK 12V relay is provided with 4 different settings and supports various triggering signal source, like positive side of power supply triggering, Button, PNP sensor, PLC signal, which is available for most of applications..
WIDE ADJUSTABLE TIMING RANGE: This off delay relay supports widest timing range, 0.1 seconds to 999 minutes adjustable, which can fulfilled your various need..
STRONG ANTI-INTERFERENCE ABILITY: The output of digital timer relay adopts optocoupler isolation, which enhances the capacity of resisting disturbance power consumption..
SUPER SIMPLE OPERATION: Our relay board is operated by buttons and the delay module is equipped with LED digital display which is convenient for you to check the set value..
AUTOMATIC SAVING FUNCTION: After you finish the setting, you can cut off the power and then the parameters will be saved automatically, handy and convenient..

Check Stock

Winch Solenoid Relay 12V ATV Winch Solenoid Relay Contactor & Winch Rocker Switch Set Fits for ATV UTV Truck

Fitment: for ATV Winch Solenoid Relay Contactor Switch 12V 250 AMP 1500lb-5000lb.
Replace Part NO. : 63070, 62135, 74900, 2875714, 70715.
Specification: Voltage: 12V, Power: 250A, 1500-5000lbs Capacity.
Applications: For 12 volt solenoid operated winches: for 4x4 vehicles, ATV's, UTV's, SUV's and Others.
Package Includes: 1 x 12V Winch Solenoid Relay Contactor, 1 x Winch Contactor Rocker Thumb Switch, 1 Set of Mounting Brackets, 6 x Insulated Protecting Waterproof Caps.

Check Stock

United Pacific 46153 High Power 126db Dixie Air Horn Kit

Train Horn For Truck: Car horns can be widely used on vehicles that has a 12V DC power, like cars, trucks, vans, tractors, boats, etc.
High-Quality Dixie Horn: Dukes of Hazzard horn has high and low tones, can blare out a loud and powerful warning Sound. Air horns are made of....
Striking Appearance: 5 Red trumpets have 5.5", 7.0", 8.0", 9.5", and 10" in length. The car horn kit includes a polished black compressor, it will....
Package Contents: 5 Trumpet air horns, 1 air compressor, air tubing, mounting hardware, 12V Relay.
Easy Installation: Air horns can be installed easily with mounting hardware and a relay included in the complete Dixie horn kit.

Check Stock

2 Packs 2-Pin 12V Speed Adjustable LED Electronic Flasher Relay Fixes Motorcycle Turn Signal and Hazard Warn Hyper Flash - Premium Version Orange DC12V-FM Part by MQparts

✅ WHAT YOU GET: 2 x 2-Pin 12V Electronic LED Flasher Relay. Model name: Orange DC12V-FM. It allows you can adjust the blinking speed of the LED....
✅ SPECIFICATIONS: Operating Voltage: 12V (11V-15V).
Flashing Frequency: 50 times/min to 200 times/min.
✅ PLUG AND PLAY: The 12V flasher relay is compatible with most 2-pin flashers and works for most brands of motorcycles or bikes (Honda, Kawasaki,....
✅ PREMIUM QUALITY: Don't waste your time and money on cheap products that can only last 1 -2 months. They are made of cheap materials and don't meet....
✅ MONEY-BACK GUARANTEE: MQparts is especially interested in customer experience. If for any reason you're not completely satisfied, you can ask for....

Check Stock

1PZ SR1-H01 Universal Light Turn Signal Switch + Flasher Relay + Horn Replacement for Honda KTM Suzuki Kawasaki Yamaha Motorcycle Dirt Bike

Left side control switch + 2 pin flasher relay + 12V round horn speaker.
Compatible for Honda, Kawasaki, KTM, Suzuki, Yamaha and many other brands as well.
Works perfectly with 12V Motorcycle Motorbike LED Turn Signal Indicator Blinker Amber Light.
It has turn signal switch, horns switch and hi/lo beam switch, fit all 7/8" handlebars.
The Max Power of the relay is 42W, which mean the power of your ( all ) LED bulbs must lower than 42 W. If more than 42W, load resistors may be required.
IMPORTANT NOTE!!! Please see buy options on the RIGHT if you need your item sooner>>>>.

Check Stock

MPSSAA Side Step Running Board for Land Rover for Range Rover Sport 2008-2013 Bar Intelligent Electric Automatic Switch Door Control Running Board Side Step

30A High Current 12V Contactor relay Switch DC power Switching Control Board.
Using high-quality ultra-small optocoupler, anti-interference ability, stable performance..
Using 9.5mm black fence terminal, standard 30A terminal, stable and solid, reliable quality..

Check Stock

Aoicrie 5Pcs DC 12V 1 Channel Relay Module Board Shield with Optocoupler Isolation Support High or Low Level Compatible Development Board Trigger

This Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.each relay has normally open and normally closed contact. Can be selected by jumper relay and TTL or ground..
Main Specification Peak Load of NO Connector: AC 250V/10A, DC 30V/10A.
These Relay Board use photocoupler isolation that has strong driving ability and stable performance.The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input.
Using SMD optocoupler isolation, strong driving capability, stable performance.Fault tolerant design, even if the control line is broken, the relay will not operate.
And interface design humanized, all the interface can be directly connected through the terminal lead, so convenient..
Wide Application These 12V relay board works well with for ARM /PIC /AVR /MCU/Raspberry/CNC machine etc..

Check Stock